- 您现在的位置：买卖IC网 > Datasheet目录364 > SSL3250AHN/C1,528 (NXP Semiconductors)IC LED DRVR PHOTO FLASH 16-HVQFN Datasheet资料下载
参数资料
| 型号： | SSL3250AHN/C1,528 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 10/26页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR PHOTO FLASH 16-HVQFN |
| 产品培训模块： | LED Controllers |
| 标准包装： | 1 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 闪灯/白光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 1.08MHz ~ 1.32MHz |
| 电源电压： | 2.7 V ~ 5.5 V |
| 输出电压： | 9.5V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-VFQFN 裸露焊盘 |
| 供应商设备封装： | 16-HVQFN |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 85°C |
| 其它名称： | 568-4718-6 |
NXP Semiconductors
SSL3250A
Photo flash dual LED driver
600
I LED (mA)
500
400
300
200
100
70
0
357
125
Flash current using direct control mode
50
Resistor
Value (k Ω )
014aaa367
Fig 8.
Flash mode LED current in Direct enable mode
8.3.5 Timed Flash mode
The timed operation of the Flash mode can only be used in the I 2 C interface mode. When
the flash is used in Timed mode (bit 4, TO_DEF = 1 in Timer control register 01h), the
internal timer will switch off the main LED after the preprogrammed maximum time in the
timer control register has expired.
The timer starts when the Flash mode is activated either by the software strobe
(FLASH_STRB bit in register 02h) or by a LOW to HIGH transition of the hardware strobe
(STRB pin) signal.
In timed mode strobing of the flash is edge sensitive, therefore the flash time is
independent of the level of the software or hardware strobe signal. The flash time is set
according to Equation 5 :
t flash = 820 ms – Register × 54.6 ms
(5)
Once the Flash time has expired no interrupt will be generated nor will it be flagged in the
status register. A new flash period can be started immediately after the previous timed
flash period has expired.
8.3.6 Flash mode during RF transmit
Although the driver is not equipped with a separate TXMASK pin, the device can operate
like that to lower the current in the main LED in Flash mode during an RF transmission in
a mobile phone application. An external switch can be connected to the resistor
controlling the nominal current value for the Flash mode. By lowering the current in the
main LED, the inductor current and therefore the current drawn from the battery will be
lowered. Reducing the inductor current has to be fast because the inductor current is
reduced within 50 μ s after changing the nominal current level to a lower setting. At the end
of the transmission period, the main LED current can be increased again to the nominal
current level. A soft start circuit will increase the inductor current with a limited slope as
defined by the soft start settings. See Section 8.5 .
SSL3250A_5
? NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 05 — 16 December 2009
10 of 26
相关PDF资料 |
PDF描述 |
|---|---|
| SST25LF020A-33-4C-QAE-T | IC FLASH SER 2MB 33HZ SPI 8WSON |
| SST25VF010A-33-4I-QAE-T | IC FLASH SER 1MB 33MHZ SPI 8WSON |
| SST25VF016B-50-4C-S2AF-T | IC FLASH SER 16M 50MHZ SPI 8SOIC |
| SST25VF020-20-4C-QAE-T | IC FLASH SER 2MB 20MHZ SPI 8WSON |
| SST25VF020B-80-4C-QAE-T | IC FLASH SER 2MB 80MHZ SPI 8WSON |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SSL3252 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Smart, simple solutions for the 12 most common design concerns |
| SSL3252UK/C2,515 | 功能描述:LED照明驱动器 Photo flash LED driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| SSL33 | 功能描述:肖特基二极管与整流器 Low VF 3Amp 30v SMD Schottky Rect RoHS:否 制造商:Skyworks Solutions, Inc. 产品:Schottky Diodes 峰值反向电压:2 V 正向连续电流:50 mA 最大浪涌电流: 配置:Crossover Quad 恢复时间: 正向电压下降:370 mV 最大反向漏泄电流: 最大功率耗散:75 mW 工作温度范围:- 65 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-143 封装:Reel |
| SSL33 R6 | 制造商:SKMI/Taiwan 功能描述:Diode Schottky 30V 3A 2-Pin SMC T/R |
| SSL34 | 功能描述:肖特基二极管与整流器 Low VF 3Amp 40v SMD Schottky Rect RoHS:否 制造商:Skyworks Solutions, Inc. 产品:Schottky Diodes 峰值反向电压:2 V 正向连续电流:50 mA 最大浪涌电流: 配置:Crossover Quad 恢复时间: 正向电压下降:370 mV 最大反向漏泄电流: 最大功率耗散:75 mW 工作温度范围:- 65 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-143 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。