- 您现在的位置：买卖IC网 > PDF目录10199 > SSM2160SZ (Analog Devices Inc)IC BALANCE/VOL CTRL DGITL 24SOIC PDF资料下载
参数资料
| 型号： | SSM2160SZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 3/16页 |
| 文件大小： | 0K |
| 描述： | IC BALANCE/VOL CTRL DGITL 24SOIC |
| 产品变化通告： | Product Discontinuance 27/Oct/2011 |
| 标准包装： | 31 |
| 类型： | 立体声音量控制 |
| 应用： | 解码器，接收器，环绕系统 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 24-SOIC W |
| 包装： | 管件 |
| 产品目录页面： | 775 (CN2011-ZH PDF) |
REV. A
SSM2160
–11–
from a gain condition to an attenuation. The master and channel
step sizes default to 1 dB in the absence of external components.
The step sizes can be changed by the addition of external resistors
if finer resolution is desired.
Control Range vs. Step Size
Before adjusting step sizes from the standard 1 dB, consider the
effect on control range. The master control and the channel
control provide 1 dB step sizes, which may be modified by the
addition of external resistors. As the total number of steps is
unchanged, reduction of the step size results in a smaller control
range. The range of the control is
RANGE
Step Size dB
Number of Levels Used
=
() × ()
Since the master volume control operates from a 7-bit word, its
DAC has 128 levels (including 0). The channel volume control
DAC is a 5-bit input, so there are 32 levels for volume control
(including 0). As can be seen in Figure 9, the practical control
range is set by the noise floor. It can be advantageous to reduce
the master step size to give finer steps from zero attenuation
down to the noise floor.
Reducing Master Step Size
To reduce the master step size, place resistor RM between
MSTR SET and MSTR OUT. The master step size of the
master volume control will then become
R
X
M
=
1700
1–
where XM is the desired master control step size in decibels. See
Figure 10 for practical values of RM. Note that the step size for
the master control can only be adjusted to less than 1 dB. No
resistor is required for the default value of 1 dB per step. For
larger step sizes, use digital control. Noninteger dB step sizes can
be obtained by using digital control and a reduced step size.
RM
1.0
0.8
0
102
105
103
MASTER
STEP
SIZE
–
dB
104
0.6
0.4
0.2
Figure 10. Master Step Size vs. RM
Example: Modifying Master Step Size to 0.5 dB
A master step size of 0.5 dB is desired for the master control,
while a 1 dB step size is adequate for the channel control. Using
the preceding equation or Figure 10, RM is found to be 1700
and is connected between MSTR SET and MSTR OUT. There
could be some variation from lot to lot, so applications requiring
precise step size should include a fixed resistor plus a trimmer
potentiometer to span the calculated value
±25%. In this example,
RC is not needed since the default channel step size is already 1 dB.
CH SET is left floating. With this step size, the dynamic range
of the master control is
DNR
dB
=×
=
05
127
635
..
In this configuration, the maximum master volume is 0 dB,
while the minimum volume is –63.5 dB. Since the channel
volume can still provide 0 dB to 31 dB of gain, the total system
gain can vary between –63.5 dB and +32 dB. Note that a 0 dB
command setting to the master control always results in unity
gain, regardless of the step size.
Channel Step Size
The channel DACs’ full-scale current is set by an internal resis-
tor to V+. By shunting this resistor, the full-scale current, and
therefore the step size, will increase. No provisions are available
for reducing the channel step size. To increase the channel step
size, place a resistor, RC, from CH SET to V+. Note that a 0 dB
setting for a channel will always give unity gain, regardless of
how large or small the step size is. This is true for both the
master and channel volume controls.
RC
1.5
1.4
1.0
101
103
102
CHANNEL
STEP
SIZE 1.3
1.2
1.1
Figure 11. Channel Step Size vs. RC
Example: Modifying Channel Step Size
A channel step size of 1.3 dB is desired. From Figure 11 we see
that a 40
resistor (approximately) connected from CH SET to
V+ is required. As this varies from lot to lot, the exact value
should be determined empirically, or a fixed resistor plus trimmer
potentiometer should be used. Take care not to short Pin 24 to
Pin 1 as damage will result.
Muting
The SSM2160 offers master and channel muting. On power-up,
the master mute is activated, thus preventing any transients
from entering the signal path and possibly overloading amplifi-
ers down the signal path. Mute is typically better than –95 dB
relative to a 0 dBu input. Due to design limitations, the indi-
vidual channel muting results in increased signal distortion in
the unmuted channels. Users should determine if this condition
is acceptable in the particular application.
相关PDF资料 |
PDF描述 |
|---|---|
| MS27473T18A32PB | CONN PLUG 32POS STRAIGHT W/PINS |
| VE-BWR-MY | CONVERTER MOD DC/DC 7.5V 50W |
| EN3P15F26SX | CONN RCPT 15POS FEMALE PANEL #26 |
| MS3100E28-6P | CONN RCPT 3POS WALL MNT W/PINS |
| PT00A-12-10P | CONN RCPT 10 POS WALL MNT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SSM2160SZ-REEL | 功能描述:IC CTRLR DGTL VOL/CHAN 24SOIC RoHS:是 类别:集成电路 (IC) >> 线性 - 音频处理 系列:- 其它有关文件:STA321 View All Specifications 标准包装:1 系列:Sound Terminal™ 类型:音频处理器 应用:数字音频 安装类型:表面贴装 封装/外壳:64-LQFP 裸露焊盘 供应商设备封装:64-LQFP EP（10x10） 包装:Digi-Reel® 其它名称:497-11050-6 |
| SSM2161 | 制造商:AD 制造商全称:Analog Devices 功能描述:6- and 4-Channel, Serial Input Master/Balance Volume Controls |
| SSM2161N | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Tone/Volume/Balance Control |
| SSM2161P | 制造商:AD 制造商全称:Analog Devices 功能描述:6- and 4-Channel, Serial Input Master/Balance Volume Controls |
| SSM2161R | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Tone/Volume/Balance Control |
发布紧急采购，3分钟左右您将得到回复。