- 您现在的位置：买卖IC网 > PDF目录225233 > SSQE48T25015-PABN (POWER-ONE INC) 1-OUTPUT 37.5 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | SSQE48T25015-PABN |
| 厂商： | POWER-ONE INC |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 37.5 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | ROHS COMPLIANT, SIXTEENTH BRICK PACKAGE-8 |
| 文件页数： | 7/12页 |
| 文件大小： | 449K |
| 代理商： | SSQE48T25015-PABN |
ZD-02084 Rev. 1.2
www.power-one.com
Page 4 of 12
SSQE48T25015 DC-DC Converter Data Sheet
36-75 VDC Input; 1.5 VDC, 25 A Output
Data Sheet
Operations
Input and Output Impedance
These power converters have been designed to be
stable with no external capacitors when used in low
inductance input and output circuits.
However, in some applications, the inductance
associated with the distribution from the power
source to the input of the converter can affect the
stability of the converter. A 33 F electrolytic
capacitor with an ESR < 1
across the input is
recommended to ensure stability of the converter
over the wide range of input source impedance.
In many applications, the user has to use decoupling
capacitance at the load. The power converter will
exhibit
stable
operation
with
external
load
capacitance up to 30,000 F.
ON/OFF (Pin 2)
The ON/OFF pin is used to turn the power converter
on or off remotely via a system signal. There are two
remote
control
options
available,
positive
and
negative logic, both referenced to Vin(-). A typical
connection is shown in Fig. A.
Rload
Vin
CONTROL
INPUT
Vin (+)
Vin (-)
ON/OFF
Vout (+)
Vout (-)
TRIM
SENSE (+)
SENSE (-)
(Top View)
SSQE48 Converter
Fig. A: Circuit configuration for ON/OFF function.
The positive logic version turns on when the ON/OFF
pin is at a logic high and turns off when the pin is at a
logic low. The converter is on when the ON/OFF pin
is left open. See the Electrical Specifications for logic
high/low definitions.
The negative logic version turns on when the pin is
at a logic low and turns off when the pin is at a logic
high. The ON/OFF pin can be hard wired directly to
Vin(-) to enable automatic power up of the converter
without the need of an external control signal.
The ON/OFF pin is internally pulled up to 5 V
through
a
resistor.
A
properly
de-bounced
mechanical switch, open-collector transistor, or FET
can be used to drive the input of the ON/OFF pin.
The device must be capable of sinking up to 0.2 mA
at a low level voltage of
0.8 V. An external voltage
source (±20 V maximum) may be connected directly
to the ON/OFF input, in which case it must be
capable of sourcing or sinking up to 1 mA depending
on the signal polarity. See the Startup Information
section for system timing waveforms associated with
use of the ON/OFF pin.
Remote Sense (Pins 5 and 7)
The
remote
sense
feature
of
the
converter
compensates for voltage drops occurring between
the output pins of the converter and the load. The
SENSE(-) (Pin 5) and SENSE(+) (Pin 7) pins should
be connected at the load or at the point where
regulation is required (see Fig. B).
100
10
Rw
Rload
Vin
Vin (+)
Vin (-)
ON/OFF
Vout (+)
Vout (-)
TRIM
SENSE (+)
SENSE (-)
(Top View)
SSQE48 Converter
Fig. B: Remote sense circuit configuration.
CAUTION
If remote sensing is not utilized, the SENSE(-) pin must be
connected to the Vout(-) pin (Pin 4), and the SENSE(+) pin
must be connected to the Vout(+) pin (Pin 8) to ensure the
converter will regulate at the specified output voltage. If these
connections are not made, the converter will deliver an
output voltage that is slightly higher than the specified data
sheet value.
Because the sense leads carry minimal current,
large traces on the end-user board are not required.
However, sense traces should be run side by side
and located close to a ground plane to minimize
system noise and ensure optimum performance.
The converters output overvoltage protection (OVP)
senses the voltage across Vout(+) and Vout(-), and
not across the sense lines, so the resistance (and
resulting voltage drop) between the output pins of
the converter and the load should be minimized to
prevent unwanted triggering of the OVP.
When utilizing the remote sense feature, care must
be taken not to exceed the maximum allowable
output power capability of the converter, which is
equal to the product of the nominal output voltage
and the allowable output current for the given
conditions.
When using remote sense, the output voltage at the
converter can be increased by as much as 10%
above the nominal rating in order to maintain the
required voltage across the load. Therefore, the
相关PDF资料 |
PDF描述 |
|---|---|
| SST-1 | SIP32, IC SOCKET |
| SST270T1 | P-CHANNEL, Si, SMALL SIGNAL, JFET |
| SSTA63T216 | 500 mA, 30 V, PNP, Si, SMALL SIGNAL TRANSISTOR |
| SSTPAD5 | 0.01 A, SILICON, SIGNAL DIODE |
| ST-MS-7-56 | POWER TRANSFORMER, 36 VA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SSQE48T25015-PABNG | 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| SSQE48T25018-NAANG | 制造商:Power-One 功能描述:Module DC-DC 1-OUT 1.8V 25A 8-Pin 1/16-Brick |
| SSQE48T25018-NAB0G | 制造商:Power-One 功能描述:DCDC - Bulk |
| SSQE48T25018-NABNG | 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| SSQE48T25018-PAA0 | 制造商:Power-One 功能描述:- Bulk |
发布紧急采购，3分钟左右您将得到回复。