参数资料
型号: SSQE48T25025-PABNG
厂商: Power-One
文件页数: 6/12页
文件大小: 0K
描述: DC/DC SIXTEENTH BRICK
标准包装: 98
系列: *
SSQE48T25025 DC-DC Converter
36-75 VDC Input; 2.5 VDC, 25 A Output
Data Sheet
Protection Features
Input Undervoltage Lockout
Input undervoltage lockout is standard with this
converter. The converter will shut down when the
input voltage drops below a pre-determined voltage.
The input voltage must be typically 34 V for the
converter to turn on. Once the converter has been
turned on, it will shut off when the input voltage
drops typically below 32 V. This feature is beneficial
in preventing deep discharging of batteries used in
telecom applications.
Output Overcurrent Protection (OCP)
The converter is protected against overcurrent or
short circuit conditions. Upon sensing an overcurrent
condition, the converter will switch to constant
current operation and thereby begin to reduce output
voltage. During short circuit, when the output voltage
drops below 50% its nominal value, the converter will
shut down.
Once the converter has shut down, it will attempt to
restart nominally every 200 ms with a very low duty
cycle. The attempted restart will continue indefinitely
until the overload or short circuit conditions are
removed.
UL60950 and EN60950. Basic Insulation is provided
between input and output.
The converters have no internal fuse. If required, the
external fuse needs to be provided to protect the
converter from catastrophic failure. Refer to the
“Input Fuse Selection for DC/DC converters”
application note on www.power-one-com for proper
selection of the input fuse. Both input traces and the
chassis ground trace (if applicable) must be capable
of conducting a current of 1.5 times the value of the
fuse without opening. The fuse must not be placed
in the grounded input line.
Abnormal and component failure tests were
conducted with the input protected by an external
UL-listed fuse, rated 20A. If a fuse rated greater
than 20A is used, additional testing may be required.
To protect a group of converters with a single fuse,
the rating can be increased from the recommended
value above.
Electromagnetic Compatibility (EMC)
EMC requirements must be met at the end-product
system level, as no specific standards dedicated to
EMC characteristics of board mounted component
DC-DC converters exist. However, Power-One tests
its converters to several system level standards,
primary of which is the more stringent EN55022,
Once the output current is brought back into its
Information technology equipment
-
Radio
specified range, the converter automatically exits the
hiccup mode and continues normal operation.
Output Overvoltage Protection (OVP)
The converter will shut down if the output voltage
across Vout(+) (Pin 8) and Vout(-) (Pin 4) exceeds
the threshold of the OVP circuitry. The OVP circuitry
contains its own reference, independent of the output
voltage regulation loop. Once the converter has shut
down, it will attempt to restart every 200 ms until the
OVP condition is removed.
Overtemperature Protection (OTP)
The converter will shut down under an
overtemperature condition to protect itself from
overheating caused by operation outside the thermal
derating curves, or operation in abnormal conditions
disturbance characteristics-Limits and methods of
measurement .
An effective internal LC differential filter significantly
reduces input reflected ripple current, and improves
EMC.
With the addition of a simple external filter, all
versions of the SSQE48T25025 converters pass the
requirements of Class B conducted emissions per
EN55022 and FCC requirements. Please contact
Power-One Applications Engineering for details of
this testing.
such as system fan failure.
Converter
will
automatically restart after it has cooled to a safe
operating temperature.
Safety Requirements
The converters meet North American and
International safety regulatory requirements per
ZD-02089 Rev. 1.1
www.power-one.com
Page 6 of 12
相关PDF资料
PDF描述
SSQL48T20033-NAABG CONV DC-DC 3.3V 20A 1/16 BRICK
ST5ER504 TRIMMER 500K OHM 0.25W SMD
ST7ETB503 TRIMMER 50K OHM 0.25W SMD
SXR471M016ST CAP ALUM 470UF 16V 20% RADIAL
T0053278670 PUD151R POWER UNIT 230V
相关代理商/技术参数
参数描述
SSQE48T25033-NAAN 制造商:Power-One 功能描述:SSQE series 3.3 V 25 A Single Output DC/DC Converter
SSQE48T25033-NAANG 功能描述:DC/DC转换器 3.3v 25A NEG TH .188" PL /16TH BRICK RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压(标称): 输出端数量:1 输出电压(通道 1):3.3 V 输出电流(通道 1):600 mA 输出电压(通道 2): 输出电流(通道 2): 安装风格:SMD/SMT 封装 / 箱体尺寸:
SSQE48T25033-NABNG 功能描述:DC/DC转换器 3.3V 25A NEG TH .145" PL /16TH BRICK RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压(标称): 输出端数量:1 输出电压(通道 1):3.3 V 输出电流(通道 1):600 mA 输出电压(通道 2): 输出电流(通道 2): 安装风格:SMD/SMT 封装 / 箱体尺寸:
SSQE48T25033-PAANG 功能描述:DC/DC转换器 3.3V 25A POS TH .188" PL /16TH BRICK RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压(标称): 输出端数量:1 输出电压(通道 1):3.3 V 输出电流(通道 1):600 mA 输出电压(通道 2): 输出电流(通道 2): 安装风格:SMD/SMT 封装 / 箱体尺寸:
SSQE48T25033-PABNG 功能描述:DC/DC转换器 3.3V 25A POS TH .145" PL /16TH BRICK RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压(标称): 输出端数量:1 输出电压(通道 1):3.3 V 输出电流(通道 1):600 mA 输出电压(通道 2): 输出电流(通道 2): 安装风格:SMD/SMT 封装 / 箱体尺寸: