参数资料
型号: SST89V54RD2-33-C-NJE
厂商: Microchip Technology
文件页数: 3/92页
文件大小: 0K
描述: IC MCU 8BIT 24KB FLASH 44PLCC
标准包装: 26
系列: FlashFlex®
核心处理器: 8051
芯体尺寸: 8-位
速度: 33MHz
连通性: EBI/EMI,SPI,UART/USART
外围设备: 欠压检测/复位,POR,WDT
输入/输出数: 36
程序存储器容量: 16KB(16K x 8)
程序存储器类型: 闪存
EEPROM 大小: 8K x 8
RAM 容量: 1K x 8
电压 - 电源 (Vcc/Vdd): 2.7 V ~ 3.6 V
振荡器型: 外部
工作温度: 0°C ~ 70°C
封装/外壳: 44-LCC
包装: 管件
2011 Silicon Storage Technology, Inc.
DS25087A
10/11
11
FlashFlex MCU
SST89V54RD2/RD / SST89V58RD2/RD
Not Recommended for New Designs
A Microchip Technology Company
Reset Configuration of Program Memory Block Switching
Program memory block switching is initialized after reset according to the state of the Start-up Config-
uration bit SC0 and/or SC1. The SC0 and SC1 bits are programmed via an external host mode com-
mand or an IAP Mode command. See Table 13.
Once out of reset, the SFCF[0] bit can be changed dynamically by the program for desired effects.
Changing SFCF[0] will not change the SC0 bit.
Caution must be taken when dynamically changing the SFCF[0] bit. Since this will cause different
physical memory to be mapped to the logical program address space. The user must avoid executing
block switching instructions within the address range 0000H to 1FFFH.
Data RAM Memory
The data RAM has 1024 bytes of internal memory. The RAM can be addressed up to 64KB for external
data memory.
Expanded Data RAM Addressing
The SST89V5xRDx both have the capability of 1K of RAM. See Figure 7.
The device has four sections of internal data memory:
1.
The lower 128 Bytes of RAM (00H to 7FH) are directly and indirectly addressable.
2.
The higher 128 Bytes of RAM (80H to FFH) are indirectly addressable.
3.
The special function registers (80H to FFH) are directly addressable only.
4.
The expanded RAM of 768 Bytes (00H to 2FFH) is indirectly addressable by the move
external instruction (MOVX) and clearing the EXTRAM bit. (See “Auxiliary Register
(AUXR)” in Section , “Special Function Registers”)
Since the upper 128 bytes occupy the same addresses as the SFRs, the RAM must be accessed indi-
rectly. The RAM and SFRs space are physically separate even though they have the same addresses.
When instructions access addresses in the upper 128 bytes (above 7FH), the MCU determines
whether to access the SFRs or RAM by the type of instruction given. If it is indirect, then RAM is
accessed. If it is direct, then an SFR is accessed. See the examples below.
Table 3: SFCF Values Under Different Reset Conditions
SC11
1. P = Programmed (Bit logic state = 0),
U = Unprogrammed (Bit logic state = 1)
SC01
State of SFCF[1:0] after:
Power-on
or
External
Reset
WDT Reset
or
Brown-out
Reset
Software
Reset
U (1)
00
(default)
x0
10
U (1)
P (0)
01
x1
11
P (0)
U (1)
10
P (0)
11
T0-0.0 25087
相关PDF资料
PDF描述
MMCX-P-178B/U CONN MMCX PLUG STRAIGHT RG178
VE-23T-IX-S CONVERTER MOD DC/DC 6.5V 75W
MMCX-P-FHSB CONN MMCX PLUG STRAIGHT FHSB
PIC24F08KA102T-I/ML IC PIC MCU FLASH 8KB 28-QFN
VI-213-IX-S CONVERTER MOD DC/DC 24V 75W
相关代理商/技术参数
参数描述
SST89V54RD2-33-C-NJE1 制造商:SST 制造商全称:Silicon Storage Technology, Inc 功能描述:FlashFlex51 MCU
SST89V54RD2-33-C-NJF2 制造商:SST 制造商全称:Silicon Storage Technology, Inc 功能描述:FlashFlex51 MCU
SST89V54RD2-33-C-PI 制造商:SST 制造商全称:Silicon Storage Technology, Inc 功能描述:FlashFlex51 MCU
SST89V54RD2-33-C-PIE1 制造商:SST 制造商全称:Silicon Storage Technology, Inc 功能描述:FlashFlex51 MCU
SST89V54RD2-33-C-PIF2 制造商:SST 制造商全称:Silicon Storage Technology, Inc 功能描述:FlashFlex51 MCU