参数资料
| 型号： | ST16C2552CJ44TR-F |
| 厂商： | Exar Corporation |
| 文件页数： | 11/34页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 16B DUAL 44PLCC |
| 标准包装： | 500 |
| 特点： | * |
| 通道数： | 2，DUART |
| FIFO's： | 16 字节 |
| 规程： | RS232，RS485 |
| 电源电压： | 3.3 V ~ 5 V |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-LCC（J 形引线） |
| 供应商设备封装： | 44-PLCC（16.59x16.59） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
ST16C2552
19
REV. 4.2.2
2.97V TO 5.5V DUAL UART WITH 16-BYTE FIFO
ISR[3:1]: Interrupt Status
These bits indicate the source for a pending interrupt at interrupt priority levels (See Interrupt Source Table 8).
ISR[5:4]: Reserved
ISR[7:6]: FIFO Enable Status
These bits are set to a logic 0 when the FIFOs are disabled. They are set to a logic 1 when the FIFOs are
enabled.
4.6
FIFO Control Register (FCR) - Write-Only
This register is used to enable the FIFOs, clear the FIFOs, set the transmit/receive FIFO trigger levels, and
select the DMA mode. The DMA, and FIFO modes are defined as follows:
FCR[0]: TX and RX FIFO Enable
Logic 0 = Disable the transmit and receive FIFO (default).
Logic 1 = Enable the transmit and receive FIFOs. This bit must be set to logic 1 when other FCR bits are
written or they will not be programmed.
FCR[1]: RX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No receive FIFO reset (default)
Logic 1 = Reset the receive FIFO pointers and FIFO level counter logic (the receive shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No transmit FIFO reset (default).
Logic 1 = Reset the transmit FIFO pointers and FIFO level counter logic (the transmit shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[3]: DMA Mode Select
Controls the behavior of the TXRDY# and RXRDY# pins. See DMA operation section for details.
Logic 0 = Normal Operation (default).
Logic 1 = DMA Mode.
FCR[5:4]: Reserved
FCR[7:6]: Receive FIFO Trigger Select
(logic 0 = default, RX trigger level =1)
These 2 bits are used to set the trigger level for the receive FIFO. The UART will issue a receive interrupt when
the number of the characters in the FIFO crosses the trigger level. Table 9 shows the complete selections.
TABLE 9: TRANSMIT AND RECEIVE FIFO TRIGGER LEVEL SELECTION
BIT-7
BIT-6
RECEIVE
TRIGGER
LEVEL
COMPATIBILITY
0
1
0
1
0
1
1 (default)
4
8
14
Table-A. 16C550,
16C2550, 16C2552,
16C554, 16C580 com-
patible.
FCR
相关PDF资料 |
PDF描述 |
|---|---|
| ST78C36CJ44-F | IC UART FIFO 16B 44PLCC |
| ST16C580CQ48-F | IC UART FIFO 16B 48TQFP |
| XR88C92CVTR-F | IC UART FIFO DUAL 44LQFP |
| XR88C92CJTR-F | IC UART FIFO DUAL 44PLCC |
| ST16C452CJ68TR-F | IC UART W/PAR PORT DUAL 68PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST16C2552CQ48 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:UART |
| ST16C2552IJ | 制造商:Exar Corporation 功能描述:2 CHANNEL(S), 4M bps, SERIAL COMM CONTROLLER, PQCC44 |
| ST16C2552IJ44 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: 制造商:Exar Corporation 功能描述:UART, 44 Pin, Plastic, PLCC |
| ST16C2552IJ44-F | 功能描述:UART 接口集成电路 2.97V-5.5V 16B FIFO temp -45 to 85C;UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| ST16C2552IJ44TR-F | 功能描述:UART 接口集成电路 DUAL UART W/16BYTE FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。