参数资料
| 型号： | ST16C2552IJ44TR-F |
| 厂商： | Exar Corporation |
| 文件页数： | 34/34页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 16B DUAL 44PLCC |
| 标准包装： | 500 |
| 特点： | * |
| 通道数： | 2，DUART |
| FIFO's： | 16 字节 |
| 规程： | RS232，RS485 |
| 电源电压： | 3.3 V ~ 5 V |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-LCC（J 形引线） |
| 供应商设备封装： | 44-PLCC（16.59x16.59） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页当前第34页
ST16C2552
9
REV. 4.2.2
2.97V TO 5.5V DUAL UART WITH 16-BYTE FIFO
2.7
INTA and INTB Ouputs
The INTA and INTB interrupt outputs change according to the operating mode and enahnced features setup.
Tables 3 and 4 summarize the operating behavior for the transmitter and receiver. Also see Figures 16
through 21.
TABLE 3: INTA AND INTB PINS OPERATION FOR TRANSMITTER
FCR BIT-0 = 0
(FIFO DISABLED)
FCR BIT-0 = 1
(FIFO ENABLED)
INTA/B Pin
0 = a byte in THR
1 = THR empty
0 = at least 1 byte in FIFO
1 = FIFO empty
TABLE 4: INTA AND INTB PIN OPERATION FOR RECEIVER
FCR BIT-0 = 0
(FIFO DISABLED)
FCR BIT-0 = 1
(FIFO ENABLED)
INTA/B Pin
0 = no data
1 = 1 byte
0 = FIFO below trigger level
1 = FIFO above trigger level
2.8
Crystal Oscillator or Ext. Clock Input
The 2552 includes an on-chip oscillator (XTAL1 and XTAL2) to produce a clock for both UART sections in the
device. The CPU data bus does not require this clock for bus operation. The crystal oscillator provides a
system clock to the Baud Rate Generators (BRG) section found in each of the UART. XTAL1 is the input to the
oscillator or external clock buffer input with XTAL2 pin being the output. SEE”PROGRAMMABLE BAUD
FIGURE 4. TYPICAL OSCILLATOR CONNECTIONS
C1
22-47 pF
C2
22-47 pF
Y1
1.8432 MHz
to
24 MHz
R1
0-120
(Optional)
R2
500Κ1Μ
XTAL1
XTAL2
The on-chip oscillator is designed to use an industry standard microprocessor crystal (parallel resonant,
fundamental frequency with 10-22 pF capacitance load, ESR of 20-120 ohms and 100ppm frequency
tolerance) connected externally between the XTAL1 and XTAL2 pins (see Figure 2), with an external 500k
to
1 M
resistor across it. Alternatively, an external clock can be connected to the XTAL1 pin to clock the internal
baud rate generator for standard or custom rates. Typical oscillator connections are shown in Figure 4. For
further reading on oscillator circuit please see application note DAN108 on EXAR’s web site.
相关PDF资料 |
PDF描述 |
|---|---|
| ST16C450CJ44-F | IC UART SINGLE 44PLCC |
| ST16C450CP40-F | IC INTERFACE UART |
| ST16C452IJ68-F | IC UART W/PAR PORT DUAL 68PLCC |
| ST16C454IJ68TR-F | IC UART QUAD 68PLCC |
| ST16C550CJ44-F | IC UART FIFO 16B SGL 44PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST16C2552IQ48 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:UART |
| ST16C32245 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:14 BIT DUAL SUPPLY BUS TRANSCEIVER LEVEL TRANSLATOR, A SIDE SERIES RESISTOR, 2 BIT I2C LINES |
| ST16C32245LBR | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:14 BIT DUAL SUPPLY BUS TRANSCEIVER LEVEL TRANSLATOR, A SIDE SERIES RESISTOR, 2 BIT I2C LINES |
| ST16C32245TBR | 功能描述:总线收发器 14 BIT DUAL BUS RoHS:否 制造商:Fairchild Semiconductor 逻辑类型:CMOS 逻辑系列:74VCX 每芯片的通道数量:16 输入电平:CMOS 输出电平:CMOS 输出类型:3-State 高电平输出电流:- 24 mA 低电平输出电流:24 mA 传播延迟时间:6.2 ns 电源电压-最大:2.7 V, 3.6 V 电源电压-最小:1.65 V, 2.3 V 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-48 封装:Reel |
| ST16C32245TBR-E | 功能描述:开关 IC - 各种 Advanced Logic Signal Switch RoHS:否 制造商:Fairchild Semiconductor 开启电阻（最大值）: 电源电压-最大:4.4 V 电源电压-最小:2.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:WLCSP-9 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。