参数资料
| 型号： | ST16C450CQ48TR-F |
| 厂商： | Exar Corporation |
| 文件页数： | 25/28页 |
| 文件大小： | 0K |
| 描述： | IC UART SINGLE 48TQFP |
| 标准包装： | 1,500 |
| 特点： | * |
| 通道数： | 1，UART |
| FIFO's： | 1 字节 |
| 电源电压： | 2.97 V ~ 5.5 V |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-TQFP |
| 供应商设备封装： | 48-TQFP（7x7） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页
ST16C450
6
Rev. 4.20
-OP2
31
35
31
O
Output-2 (User Defined). This pin provides the user a general
purpose output. See bit-3 modem control register (MCR bit-
3).
VCC
40
44
42
Pwr
Power Supply Input.
XTAL1
16
18
14
I
Crystal or External Clock Input - Functions as a crystal input
or as an external clock input. A crystal can be connected
between this pin and XTAL2 to form an internal oscillator
circuit. An external 1 MW resistor is required between the
XTAL1 and XTAL2 pins (see figure 3). Alternatively, an
external clock can be connected to this pin to provide
custom data rates (Programming Baud Rate Generator
section).
XTAL2
17
19
15
O
Output of the Crystal Oscillator or Buffered Clock - (See also
XTAL1). Crystal oscillator output or buffered clock output.
-CD
38
42
40
I
Carrier Detect (active low) - A logic 0 on this pin indicates
that a carrier has been detected by the modem.
-CTS
36
40
38
I
Clear to Send (active low) - A logic 0 on the -CTS pin
indicates the modem or data set is ready to accept transmit
data from the ST16C450. Status can be tested by reading
MSR bit-4. This pin has no effect on the UART’s transmit or
receive operation.
-DSR
37
41
39
I
Data Set Ready (active low) - A logic 0 on this pin indicates
the modem or data set is powered-on and is ready for data
exchange with the UART. This pin has no effect on the
UART’s transmit or receive operation.
-DTR
33
37
33
O
Data Terminal Ready (active low) - A logic 0 on this pin
indicates that the ST16C450 is powered-on and ready. This
pin can be controlled via the modem control register.
Writing a logic 1 to MCR bit-0 will set the -DTR output to
logic 0, enabling the modem. This pin will be a logic 1 after
writing a logic 0 to MCR bit-0, or after a reset. This pin has
no effect on the UART’s transmit or receive operation.
SYMBOL DESCRIPTION
Symbol
Pin
Signal
Pin Description
40
44
48
type
相关PDF资料 |
PDF描述 |
|---|---|
| ST16C450IJ44TR-F | IC UART SINGLE 44PLCC |
| XR16M770IL24-F | IC UART FIFO 64B 24QFN |
| XR16M680IL32-F | IC UART FIFO 32B 32QFN |
| XR16M580IL32-F | IC UART FIFO 16B 32QFN |
| XR16M670IL24-F | IC UART FIFO 32B 24QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST16C450IJ44 | 制造商:EXAR 制造商全称:EXAR 功能描述:UNIVERSAL ASYNCHRONOUS RECEIVER/TRANSMITTER (UART) |
| ST16C450IJ44-F | 功能描述:UART 接口集成电路 SINGLE UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| ST16C450IJ44TR | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| ST16C450IJ44TR-F | 功能描述:UART 接口集成电路 SINGLE UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| ST16C450IP40 | 功能描述:UART 接口集成电路 SINGLE UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。