参数资料
型号: ST16C452CJ68TR-F
厂商: Exar Corporation
文件页数: 4/30页
文件大小: 0K
描述: IC UART W/PAR PORT DUAL 68PLCC
标准包装: 250
特点: *
通道数: 2,DUART
FIFO's: 1 字节
规程: 打印机
电源电压: 2.97 V ~ 5.5 V
带并行端口:
带故障启动位检测功能:
带调制解调器控制功能:
带CMOS:
安装类型: 表面贴装
封装/外壳: 68-LCC(J 形引线)
供应商设备封装: 68-PLCC
包装: 带卷 (TR)
12
ST16C452/452PS
Rev. 3.20
used to strobe PD0-PD7 bus data into a printer input
buffer. -SLCTIN normally selects the printer while
AutoFDXT signals the printer to auto-linefeed. Other
signals provide similar printer functions but are not bi-
directional. The printer functions for these signals are
described in table 1, Symbol Description.
The interface provides a mode steering signal called
BIDEN. BIDEN controls the bi-directional 8-bit data
bus (PD0-PD7) direction, input or output. This pin
controls the port direction in the ST16C452. A logic 0 on
this pin places the parallel port in the output mode and
a logic 1 places the parallel port in the input mode. In the
ST16C452PS, the port direction is determined as de-
scribed in Table 6. When BIDEN is a logic 1 a single
control bit (D5) in the control register sets the input or
output mode. Setting BIDEN to a logic 0 however sets
an IBM interface compatible mode. In this mode the bus
direction (input/output) is set by eight data bits in the
IOSEL register. An AA (Hex) pattern sets the input
mode while a 55 (hex) pattern sets the output mode. I/
O direction is depicted in Table 6 below.
Printer Port
The 452/452PS contains a general purpose 8-bit
parallel interface port that is designed to directly
interface with a CENTRONICS Printer. A number of
the control/interrupt signals and the 8-bit data bus
have been designed as bi-directional data buses. This
allows the interface to function with other device
parallel data bus applications. Signal -ACK is used to
generate an -INTP interface interrupt that would nor-
mally be connected to the user CPU. -INTP can be
made to follow the -ACK signal, normal mode (see
Figure 7) or it can be configured for the latch mode. In
the latch mode the interrupt is not cleared until printer
status register (SR) is read. Another signal (INIT) can
be made to function as an outgoing or incoming
interrupt, or combined with other interrupts to provide
a common wire-or interrupt output. Interface signals -
STROBE, -AutoFDXT, and -SLCTIN are bi-direc-
tional and can be used as combinations of input and/
or output functions. The signals have internal pull-up
resistors and can be wire-or’d. Normally, -STROBE is
Table 6, PD0-PD7 I/O DIRECTION MODE SELECTION [452PS only]
PORT DIRECTION
BIDEN
CONTROL REGISTER (D5)
I/O SELECT REGISTER
Input mode
0
X (Note 4)
AA Hex
Output mode
0
X (Note 4)
55 Hex
Output mode
1
0
X (Note 4)
Input mode
1
X (Note 4)
Note: 4 = don’t care
相关PDF资料
PDF描述
ST16C552CJ68TR-F IC UART FIFO 16B DUAL 68PLCC
XR68C681CJTR-F IC UART CMOS DUAL 44PLCC
ST16C2550CJ44TR-F IC UART FIFO 16B DUAL 44PLCC
XR16V2750IMTR-F IC UART FIFO 64B DUAL 48TQFP
XR88C681CJTR-F IC UART CMOS DUAL 44PLCC
相关代理商/技术参数
参数描述
ST16C452IJ68 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
ST16C452IJ68-F 功能描述:UART 接口集成电路 DUAL UART W/PARALEL PRINTER PORT RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
ST16C452IJ68PS 制造商:EXAR 制造商全称:EXAR 功能描述:DUAL UART WITH PARALLEL PRINTER PORT
ST16C452IJ68PS-F 功能描述:UART 接口集成电路 DUAL UART W/PARALEL PRINTER PORT RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
ST16C452IJ68TR-F 制造商:Exar Corporation 功能描述:UART 2-CH 3.3V/5V 68-Pin PLCC T/R 制造商:Exar Corporation 功能描述:ST16C452IJ68TR-F