参数资料
型号: ST16C552AIJ68-F
厂商: Exar Corporation
文件页数: 17/39页
文件大小: 0K
描述: IC UART FIFO 16B DUAL 68PLCC
标准包装: 19
特点: *
通道数: 2,DUART
FIFO's: 16 字节
规程: 打印机
电源电压: 2.97 V ~ 5.5 V
带并行端口:
带故障启动位检测功能:
带调制解调器控制功能:
带CMOS:
安装类型: 表面贴装
封装/外壳: 68-LCC(J 形引线)
供应商设备封装: 68-PLCC
包装: 管件
其它名称: 1016-1566-5
1016-1566-5-ND
1016-1665
ST16C552AIJ68-F-ND
24
ST16C552/552A
Rev. 3.40
MSR BIT-6:
RI (active high, logical 1). Normally this bit is the
compliment of the -RI input. In the loop-back mode
this bit is equivalent to MCR bit-2 in the MCR register.
MSR BIT-7:
CD (active high, logical 1). Normally this bit is the
compliment of the -CD input. In the loop-back mode
this bit is equivalent to MCR bit-3 in the MCR register.
Note: Whenever any MSR bit 0-3: is set to logic “1”, a
MODEM Status Interrupt will be generated.
Scratchpad Register (SPR)
The ST16C552/552A provides a temporary data reg-
ister to store 8 bits of user information.
PRINTER PORT REGISTER DESCRIPTIONS
Port Register (PR)
PR BIT 0-7:
Printer Data port (Bi-directional) - These pins are the
eight bit data bus for transferring information to or
from an external device (usually a printer). D0 is the
least significant bit. PD7-PD0 are latched during a
write cycle (output mode).
I/O Select Register (IOSEL)
This bit is used in conjunction with the state of BIDEN
to set the direction (input/output) of the PD7-PD0 data
bus. This register is used only when BIDEN is a logic
0.
Logic 55 (Hex) + BIDEN 0 = PD7-PD0 are set for
output mode
Logic AA (Hex) + BIDEN 0 = PD7-PD0 are set for input
mode
Status Register (SR)
This register provides the printer port input logical
states and the status of the interrupt -INTP based on
the condition of the -ACK printer port interface signal.
The logical state of these pins is dependent on exter-
nal interface signals.
SR BIT 1-0:
Not Used - initialized to a logic 1.
SR BIT-2:
Logic 0 = an interrupt is pending
When INTSEL is a logic 0, SR bit-2 basically tracks the
-ACK input interface pin (returns to a logic 1 when the
-ACK input returns to a logic 1). However when
INTSEL is a logic 1, the latched mode is selected, SR
bit-2 goes to a logic 0 with the -ACK input but does not
return to a logic 1 until the end of the read cycle, i.e.,
reading SR will set this bit to a logic 1.
Logic 1 = no interrupt is pending. (normal inactive
state)
SR BIT-3:
Logic 0 = -ERROR input is a logic 0.
Logic 1 = -ERROR input is a logic 1. (normal inactive
state)
SR BIT-4:
Logic 0 = SLCT input is a logic 0. (normal inactive
state)
Logic 1 = SLCT input is a logic 1.
SR BIT-5:
Logic 0 = PE input is a logic 0. (normal inactive state)
Logic 1 = PE input is a logic 1.
SR BIT-6:
Logic 0 = -ACK input is a logic 0.
Logic 1 = -ACK input is a logic 1. (normal inactive
state)
SR BIT-7:
Logic 0 = BUSY input is a logic 0
Logic 1 = BUSY input is a logic 1 (normal inactive
state)
Command Register (COM)
This register provides the printer port input logical
states and the status of the printer interrupt INIT,
which is based on the state of CON bit-1.
COM BIT-0:
-STROBE is a bi-directional signal with an open
相关PDF资料
PDF描述
MS27474T10A98P CONN RCPT 6POS JAM NUT W/PINS
XR88C192IV-F IC UART FIFO DUAL 44LQFP
MS27484T8F35PA CONN PLUG 6POS STRAIGHT W/PINS
ST16C2550IJ44-F IC UART FIFO 16B DUAL 44PLCC
VI-JWJ-IW-F2 CONVERTER MOD DC/DC 36V 100W
相关代理商/技术参数
参数描述
ST16C552CJ 制造商:STARTECH 功能描述:
ST16C552CJ68 制造商:Rochester Electronics LLC 功能描述:DUAL PORT 16 BYTE FIFO AND PARALLEL PRINTR - Bulk 制造商:Exar Corporation 功能描述:
ST16C552CJ68-F 功能描述:UART 接口集成电路 2.97V-5.5V 16B FIFO temp 0C to 70C; UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
ST16C552CJ68TR-F 功能描述:UART 接口集成电路 DUAL UART W/16BYTE FIFO&PARALELPRNTPORT RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
ST16C552IJ68 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: