参数资料
| 型号： | ST16C554DCQ64-F |
| 厂商： | Exar Corporation |
| 文件页数： | 15/39页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 16B QUAD 64LQFP |
| 标准包装： | 160 |
| 特点： | * |
| 通道数： | 4，QUART |
| FIFO's： | 16 字节 |
| 规程： | RS232 |
| 电源电压： | 2.97 V ~ 5.5 V |
| 带自动流量控制功能： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP（10x10） |
| 包装： | 托盘 |
| 其它名称： | 1016-1266 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
ST16C554/554D
22
2.97V TO 5.5V QUAD UART WITH 16-BYTE FIFO
REV. 4.0.1
MCR[3]: INT Output Enable
Enable or disable INT outputs to become active or in three-state. This function is associated with the INTSEL
input, see below table for details. This bit is also used to control the OP2# signal during internal loopback
mode. INTSEL pin must be LOW during 68 mode.
Logic 0 = INT (A-D) outputs disabled (three state) in the 16 mode (default). During internal loopback mode,
OP2# is HIGH.
Logic 1 = INT (A-D) outputs enabled (active) in the 16 mode. During internal loopback mode, OP2# is LOW.
MCR[4]: Internal Loopback Enable
Logic 0 = Disable loopback mode (default).
Logic 1 = Enable local loopback mode, see loopback section and Figure 10.
MCR[7:5]: Reserved (Default 0)
4.8
Line Status Register (LSR) - Read/Write
This register is writeable but it is not recommended. The LSR provides the status of data transfers between the
UART and the host. If IER bit-2 is enabled, LSR bit-1 will generate an interrupt immediately and LSR bits 2-4
will generate an interrupt when a character with an error is in the RHR.
LSR[0]: Receive Data Ready Indicator
Logic 0 = No data in receive holding register or FIFO (default).
Logic 1 = Data has been received and can be read from the receive holding register or RX FIFO.
LSR[1]: Receiver Overrun Flag
Logic 0 = No overrun error (default).
Logic 1 = Overrun error. A data overrun error condition occurred in the receive shift register. This happens
when additional data arrives while the FIFO is full. In this case the previous data in the receive shift register
is overwritten. Note that under this condition the data byte in the receive shift register is not transferred into
the FIFO, therefore the data in the FIFO is not corrupted by the error.
LSR[2]: Receive Data Parity Error Tag
Logic 0 = No parity error (default).
Logic 1 = Parity error. The receive character in RHR does not have correct parity information and is suspect.
This error is associated with the character available for reading in RHR.
LSR[3]: Receive Data Framing Error Tag
Logic 0 = No framing error (default).
Logic 1 = Framing error. The receive character did not have a valid stop bit(s). This error is associated with
the character available for reading in RHR.
TABLE 12: INT OUTPUT MODES
INTSEL
PIN
MCR
BIT-3
INT A-D OUTPUTS IN 16 MODE
0
Three-State
0
1
Active
1
X
Active
相关PDF资料 |
PDF描述 |
|---|---|
| ATMEGA164A-AUR | IC MCU AVR 16K 20MHZ 44TQFP |
| ATMEGA164A-MUR | IC MCU AVR 16K 20MHZ 44VQFN |
| MAX7311AAG+T | IC I/O EXPANDER I2C 16B 24SSOP |
| ST16C554DCJ68-F | IC UART FIFO 16B QUAD 68PLCC |
| XR16V554IL-F | IC UART FIFO 16B QUAD 48QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST16C554DCQ64TR-F | 功能描述:UART 接口集成电路 QUAD UART W/16 BYTE FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| ST16C554DIJ68 | 制造商:EXAR 制造商全称:EXAR 功能描述:QUAD UART WITH 16-BYTE FIFOS |
| ST16C554DIJ68-F | 功能描述:UART 接口集成电路 2.97V-5.5V 16B FIFO temp -45 to 85C;UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| ST16C554DIJ68TR-F | 功能描述:UART 接口集成电路 QUAD UART W/16 BYTE FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| ST16C554DIQ64 | 制造商:Exar Corporation 功能描述:QUAD UART W/16 BYTE FIFO |
发布紧急采购，3分钟左右您将得到回复。