参数资料
| 型号： | ST16C580CQ48-F |
| 厂商： | Exar Corporation |
| 文件页数： | 3/39页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 16B 48TQFP |
| 标准包装： | 250 |
| 特点： | * |
| 通道数： | 1，UART |
| FIFO's： | 16 字节 |
| 电源电压： | 2.97 V ~ 5.5 V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-TQFP |
| 供应商设备封装： | 48-TQFP（7x7） |
| 包装： | 托盘 |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
ST16C580
11
Rev. 1.22
C1
22pF
C2
33pF
X1
1.8432 MHz
R1
50-120
R2
1M
XTA
L
1
XTA
L
2
Crystal oscillator connection
level. In this case the 580 FIFO may hold more charac-
ters than the programmed trigger level. Following the
removal of a data byte, the user should recheck LSR bit-
0 for additional characters. A Receive Time Out will not
occur if the receive FIFO is empty. The time out counter
is reset at the center of each stop bit received or each
time the receive holding register (RHR) is read (see
Figure 10, Receive Time-out Interrupt). The actual time
out value is T (Time out length in bits) = 4 X P
(Programmed word length) + 12. To convert the time out
value to a character value, the user has to consider the
complete word length, including data information
length, start bit, parity bit, and the size of stop bit, i.e.,
1X, 1.5X, or 2X bit times.
Example -A: If the user programs a word length of 7,
with no parity and one stop bit, the time out will be:
T = 4 X 7( programmed word length) +12 = 40 bit times.
The character time will be equal to 40 / 9 = 4.4
characters, or as shown in the fully worked out ex-
ample: T = [(programmed word length = 7) + (stop bit
= 1) + (start bit = 1) = 9]. 40 (bit times divided by 9) =
4.4 characters.
Example -B: If the user programs the word length = 7,
with parity and one stop bit, the time out will be:
T = 4 X 7(programmed word length) + 12 = 40 bit times.
Character time = 40 / 10 [ (programmed word length
= 7) + (parity = 1) + (stop bit = 1) + (start bit = 1) = 4
characters.
Programmable Baud Rate Generator
The 580 supports high speed modem technologies
that have increased input data rates by employing
data compression schemes. For example a 33.6Kbps
modem that employs data compression may require a
115.2Kbps input data rate. A 128.0Kbps ISDN modem
that supports data compression may need an input
data rate of 460.8Kbps. The 580 can support a stan-
dard data rate of 921.6Kbps.
Single baud rate generator is provided for the trans-
mitter and receiver, allowing independent TX/RX
channel control. The programmable Baud Rate Gen-
erator is capable of accepting an input clock up to 24
MHz, as required for supporting a 1.5Mbps data rate.
The 580 can be configured for internal or external clock
operation. For internal clock oscillator operation, an
industry standard microprocessor crystal (parallel reso-
nant/ 22-33 pF load) is connected externally between
the XTAL1 and XTAL2 pins, with an external 1 M
resistor across it. Alternatively, an external clock can
be connected to the XTAL1 pin to clock the internal baud
rate generator for standard or custom rates.
The generator divides the input 16X clock by any
divisor from 1 to 216 -1. The 580 divides the basic
crystal or external clock by 16. Further division of this
16X clock provides two table rates to support low and
high data rate applications using the same system
design. The two rate tables are selectable through the
internal register, MCR bit-7. Setting MCR bit-7 to a
logic 1 provides an additional divide by 4 whereas,
setting MCR bit-7 to a logic 0 only divides by 1. (See
Table 4 and Figure 11). The frequency of the -
BAUDOUT output pin is exactly 16X (16 times) of the
selected baud rate (-BAUDOUT =16 x Baud Rate).
Customized Baud Rates can be achieved by selecting
the proper divisor values for the MSB and LSB sec-
tions of baud rate generator.
Programming the Baud Rate Generator Registers
相关PDF资料 |
PDF描述 |
|---|---|
| XR88C92CVTR-F | IC UART FIFO DUAL 44LQFP |
| XR88C92CJTR-F | IC UART FIFO DUAL 44PLCC |
| ST16C452CJ68TR-F | IC UART W/PAR PORT DUAL 68PLCC |
| ST16C552CJ68TR-F | IC UART FIFO 16B DUAL 68PLCC |
| XR68C681CJTR-F | IC UART CMOS DUAL 44PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST16C580IJ44 | 制造商:EXAR 制造商全称:EXAR 功能描述:UART WITH 16-BYTE FIFO’s AND INFRARED (IrDA) ENCODER/DECODER |
| ST16C580IP40 | 制造商:EXAR 制造商全称:EXAR 功能描述:UART WITH 16-BYTE FIFO’s AND INFRARED (IrDA) ENCODER/DECODER |
| ST16C580IQ48 | 制造商:EXAR 制造商全称:EXAR 功能描述:UART WITH 16-BYTE FIFO’s AND INFRARED (IrDA) ENCODER/DECODER |
| ST16C580IQ48-F | 功能描述:UART 接口集成电路 UART W/16BYTE FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| ST16C650 | 制造商:EXAR 制造商全称:EXAR 功能描述:2.90V TO 5.5V UART WITH 32-BYTE FIFO |
发布紧急采购，3分钟左右您将得到回复。