参数资料
| 型号： | ST16C650ACQ48-F |
| 厂商： | Exar Corporation |
| 文件页数： | 10/50页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 32B 48TQFP |
| 标准包装： | 250 |
| 特点： | * |
| 通道数： | 1，UART |
| FIFO's： | 32 字节 |
| 规程： | 打印机，RS232，RS422，RS485 |
| 电源电压： | 2.9 V ~ 5.5 V |
| 带并行端口： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-TQFP |
| 供应商设备封装： | 48-TQFP（7x7） |
| 包装： | 托盘 |
| 其它名称： | 1016-1662 ST16C650ACQ48-F-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
ST16C650A
18
2.90V TO 5.5V UART WITH 32-BYTE FIFO
REV. 5.0.3
control mechanisms, flow control characters are not placed (stacked) in the user accessible RX data buffer or
FIFO.
In the event that the receive buffer is overfilling and flow control needs to be executed, the 650A automatically
sends an Xoff message (when enabled) via the serial TX output to the remote modem. The 650A sends the
Xoff-1,2 characters two-character-times (= time taken to send two characters at the programmed baud rate)
after the receive FIFO crosses the programmed trigger level. To clear this condition, the 650A will transmit the
programmed Xon-1,2 characters as soon as receive FIFO drops to one trigger level below the programmed
trigger level. Table 5 below explains this:
TABLE 5: AUTO XON/XOFF (SOFTWARE) FLOW CONTROL
RX TRIGGER LEVEL
INT PIN ACTIVATION
XOFF CHARACTER(S) SENT
(CHARACTERS IN RX FIFO)
XON CHARACTER(S) SENT
(CHARACTERS IN RX FIFO)
8
8*
0
16
16*
8
24
24*
16
28
28*
24
* After the trigger level is reached, an xoff character is sent after a short span of time (= time required to send 2
characters); for example, after 2.083ms has elapsed for 9600 baud and 10-bit word length setting.
2.14
Special Character Detect
A special character detect feature is provided to detect an 8-bit character when bit-5 is set in the Enhanced
Feature Register (EFR). When this character (Xoff2) is detected, it will be placed in the FIFO along with normal
incoming RX data.
The 650A compares each incoming receive character with Xoff-2 data. If a match exists, the received data will
be transferred to the RX FIFO and ISR bit-4 will be set to indicate detection of a special character.
Although the Internal Register Table shows each X-Register with eight bits of character information, the actual
number of bits is dependent on the programmed word length. Line Control Register (LCR) bits 0-1 defines the
number of character bits, i.e., either 5 bits, 6 bits, 7 bits, or 8 bits. The word length selected by LCR bits 0-1
also determines the number of bits that will be used for the special character comparison. Bit-0 in the X-
registers corresponds with the LSB bit for the receive character.
2.15
Auto RS485 Half-duplex Control
The auto RS485 half-duplex direction control changes the behavior of the transmitter when enabled by XFR
bit-3. By default, it asserts RTS# (logic 0) output following the last stop bit of the last character that has been
transmitted. This helps in turning around the transceiver to receive the remote station’s response. When the
host is ready to transmit next polling data packet again, it only has to load data bytes to the transmit FIFO. The
transmitter automatically re-asserts RTS# (logic 1) output prior to sending the data. The RS485 half-duplex
direction control output polarity can be inverted by enabling XFR bit-5.
TABLE 6: RS485 HALF-DUPLEX CONTROL
XFR BIT-2
XFR BIT-5
RTS# PIN
0
X
RS485 Half-Duplex control disabled
1
0
Logic 1 = TX
Logic 0 = RX
1
Logic 1 = RX
Logic 0 = TX
相关PDF资料 |
PDF描述 |
|---|---|
| XR68M752IM48-F | IC UART FIFO 64B DUAL 48TQFP |
| XR16M752IM48-F | IC UART FIFO 34B DUAL 48TQFP |
| ST16C450CQ48-F | IC UART SINGLE 48TQFP |
| ST16C2450IQ48-F | IC UART FIFO DUAL 48TQFP |
| MAX7314AEG+T | IC I/O EXPANDER I2C 16B 24QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST16C650ACQ48TR-F | 制造商:Exar Corporation 功能描述:UART 1-CH 32Byte FIFO 3.3V/5V 48-Pin TQFP T/R 制造商:Exar Corporation 功能描述:ST16C650ACQ48TR-F |
| ST16C650AIJ44 | 制造商:EXAR 制造商全称:EXAR 功能描述:2.90V TO 5.5V UART WITH 32-BYTE FIFO |
| ST16C650AIJ44-F | 功能描述:UART 接口集成电路 UART W/32BYTEFIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| ST16C650AIP40 | 制造商:EXAR 制造商全称:EXAR 功能描述:2.90V TO 5.5V UART WITH 32-BYTE FIFO |
| ST16C650AIQ48 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:UART, 48 Pin, Plastic, TQFP |
发布紧急采购，3分钟左右您将得到回复。