- 您现在的位置：买卖IC网 > PDF目录11820 > ST16C654IJ68-F (Exar Corporation)IC UART FIFO 64B QUAD 68PLCC PDF资料下载
参数资料
| 型号： | ST16C654IJ68-F |
| 厂商： | Exar Corporation |
| 文件页数： | 13/51页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 64B QUAD 68PLCC |
| 标准包装： | 19 |
| 特点： | * |
| 通道数： | 4，QUART |
| FIFO's： | 64 字节 |
| 规程： | RS232 |
| 电源电压： | 2.97 V ~ 5.5 V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 68-LCC（J 形引线） |
| 供应商设备封装： | 68-PLCC |
| 包装： | 管件 |
| 其它名称： | 1016-1272 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页
ST16C654/654D
xr
2.97V TO 5.5V QUAD UART WITH 64-BYTE FIFO
REV. 5.0.2
20
2.16
Sleep Mode with Auto Wake-Up
The 654 supports low voltage system designs, hence, a sleep mode is included to reduce its power
consumption when the chip is not actively used.
All of these conditions must be satisfied for the 654 to enter sleep mode:
■ no interrupts pending for all four channels of the 654 (ISR bit-0 = 1)
■ sleep mode of both channels are enabled (IER bit-4 = 1)
■ modem inputs are not toggling (MSR bits 0-3 = 0)
■ RX input pins are idling at a logic 1
The 654 stops its crystal oscillator to conserve power in the sleep mode. User can check the XTAL2 pin for no
clock output as an indication that the device has entered the sleep mode.
The 654 resumes normal operation by any of the following:
■ a receive data start bit transition (logic 1 to 0)
■ a data byte is loaded to the transmitter, THR or FIFO
■ a change of logic state on any of the modem or general purpose serial inputs: CTS#, DSR#, CD#, RI#
If the 654 is awakened by any one of the above conditions, it will return to the sleep mode automatically after
all interrupting conditions have been serviced and cleared. If the 2750 is awakened by the modem inputs, a
read to the MSR is required to reset the modem inputs. In any case, the sleep mode will not be entered while
an interrupt is pending from any channel. The 654 will stay in the sleep mode of operation until it is disabled by
setting IER bit-4 to a logic 0.
If the address lines, data bus lines, IOW#, IOR#, CSA#, CSB#, CSC#, CSD# and modem input lines remain
steady when the 654 is in sleep mode, the maximum current will be in the microamp range as specified in the
DC Electrical Characteristics on page 37. If the input lines are floating or are toggling while the 654 is in sleep
mode, the current can be up to 100 times more. If any of those signals are toggling or floating, then an external
buffer would be required to keep the address, data and control lines steady to achieve the low current.
A word of caution: owing to the starting up delay of the crystal oscillator after waking up from sleep mode, the
first few receive characters may be lost. Also, make sure the RX A-D pins are idling at logic 1 or “marking”
condition during sleep mode. This may not occur when the external interface transceivers (RS-232, RS-485 or
another type) are also put to sleep mode and cannot maintain the “marking” condition. To avoid this, the
system design engineer can use a 47k ohm pull-up resistor on each of the RX A-D inputs.
2.17
Internal Loopback
The 654 UART provides an internal loopback capability for system diagnostic purposes. The internal loopback
mode is enabled by setting MCR register bit-4 to logic 1. All regular UART functions operate normally.
Figure 13 shows how the modem port signals are re-configured. Transmit data from the transmit shift register
output is internally routed to the receive shift register input allowing the system to receive the same data that it
was sending. The TX pin is held at logic 1 or mark condition while RTS# and DTR# are de-asserted, and
CTS#, DSR# CD# and RI# inputs are ignored. Caution: the RX input must be held to a logic 1 during loopback
test else upon exiting the loopback test the UART may detect and report a false “break” signal.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B74-IW-F2 | CONVERTER MOD DC/DC 48V 100W |
| ST16C654CJ68-F | IC UART FIFO 64B QUAD 68PLCC |
| VE-B73-IX-F4 | CONVERTER MOD DC/DC 24V 75W |
| XR17V252IM-F | IC UART PCI BUS DUAL 100TQFP |
| MS3110E14-15S | CONN RCPT 15POS WALL MNT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST16C654IJ68-F | 制造商:Exar Corporation 功能描述:IC QUAD UART 1.5MBPS 5.5V 68-PLCC |
| ST16C654IJ68TR-F | 制造商:Exar Corporation 功能描述:UART 4-CH 64Byte FIFO 3.3V/5V 68-Pin PLCC T/R 制造商:Exar Corporation 功能描述:2.97V to 5.5V Quad UART with 64 Byte FIFOs PLCC 68 制造商:Exar Corporation 功能描述:ST16C654IJ68TR-F |
| ST16C654IQ | 制造商:Exar Corporation 功能描述: |
| ST16C654IQ100 | 制造商:EXAR 制造商全称:EXAR 功能描述:QUAD UART WITH 64-BYTE FIFO AND INFRARED (IrDA) ENCODER/DECODER |
| ST16C654IQ100-F | 功能描述:UART 接口集成电路 QUAD UARTW/64BYTE FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。