参数资料
| 型号： | ST16C654IQ64-F |
| 厂商： | Exar Corporation |
| 文件页数： | 24/51页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 64B QUAD 64LQFP |
| 标准包装： | 160 |
| 特点： | * |
| 通道数： | 4，QUART |
| FIFO's： | 64 字节 |
| 规程： | RS232 |
| 电源电压： | 2.97 V ~ 5.5 V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP（10x10） |
| 包装： | 托盘 |
| 其它名称： | 1016-1273 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页
ST16C654/654D
xr
2.97V TO 5.5V QUAD UART WITH 64-BYTE FIFO
REV. 5.0.2
30
LCR[5]: TX and RX Parity Select
If the parity bit is enabled, LCR BIT-5 selects the forced parity format.
LCR BIT-5 = logic 0, parity is not forced (default).
LCR BIT-5 = logic 1 and LCR BIT-4 = logic 0, parity bit is forced to a logical 1 for the transmit and receive
data.
LCR BIT-5 = logic 1 and LCR BIT-4 = logic 1, parity bit is forced to a logical 0 for the transmit and receive
data.
LCR[6]: Transmit Break Enable
When enabled, the Break control bit causes a break condition to be transmitted (the TX output is forced to a
“space’, logic 0, state). This condition remains, until disabled by setting LCR bit-6 to a logic 0.
Logic 0 = No TX break condition. (default)
Logic 1 = Forces the transmitter output (TX) to a “space”, logic 0, for alerting the remote receiver of a line
break condition.
LCR[7]: Baud Rate Divisors Enable
Baud rate generator divisor (DLL/DLM) enable.
Logic 0 = Data registers are selected. (default)
Logic 1 = Divisor latch registers are selected.
4.7
Modem Control Register (MCR) or General Purpose Outputs Control - Read/Write
The MCR register is used for controlling the serial/modem interface signals or general purpose inputs/outputs.
MCR[0]: DTR# Output
The DTR# pin is a modem control output. If the modem interface is not used, this output may be used as a
general purpose output.
Logic 0 = Force DTR# output to a logic 1 (default).
Logic 1 = Force DTR# output to a logic 0.
MCR[1]: RTS# Output
The RTS# pin is a modem control output and may be used for automatic hardware flow control by enabled by
EFR bit-6. If the modem interface is not used, this output may be used as a general purpose output.
Logic 0 = Force RTS# output to a logic 1 (default).
Logic 1 = Force RTS# output to a logic 0.
MCR[2]: Reserved
OP1# is not available as an output pin on the 654. But it is available for use during Internal Loopback Mode. In
the Loopback Mode, this bit is used to write the state of the modem RI# interface signal.
TABLE 13: PARITY SELECTION
LCR BIT-5 LCR BIT-4 LCR BIT-3
PARITY SELECTION
X
0
No parity
0
1
Odd parity
0
1
Even parity
1
0
1
Force parity to mark,
“1”
1
Forced parity to
space, “0”
相关PDF资料 |
PDF描述 |
|---|---|
| XR16V654IV-F | IC UART FIFO 64B QUAD 64LQFP |
| ST16C654CQ64-F | IC UART FIFO 64B QUAD 64LQFP |
| ST16C654DCQ64-F | IC UART FIFO 64B QUAD 64LQFP |
| ST16C654IQ100-F | IC UART FIFO 64B QUAD 100QFP |
| XR16V654IL-F | IC UART FIFO 64B QUAD 48QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST16C654IQ64-F | 制造商:Exar Corporation 功能描述:IC QUAD UART 1.5MBPS 5.5V 64-LQFP 制造商:Exar Corporation 功能描述:IC, QUAD UART, 1.5MBPS, 5.5V, 64-LQFP |
| ST16C654IQ64TR-F | 制造商:Exar Corporation 功能描述:UART 4-CH 64Byte FIFO 3.3V/5V 64-Pin LQFP T/R 制造商:Exar Corporation 功能描述:ST16C654IQ64TR-F |
| ST16CF54 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Smartcard MCU With 4 KBytes EEPROM 512 Bits Modular Arithmetic Processor |
| ST16CQ32245TBR | 功能描述:开关 IC - 各种 Advanced Logic Signal Switch RoHS:否 制造商:Fairchild Semiconductor 开启电阻（最大值）: 电源电压-最大:4.4 V 电源电压-最小:2.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:WLCSP-9 封装:Reel |
| ST16DD00 | 功能描述:拨动开关 TOGGLE RoHS:否 制造商:C&K Components 触点形式:DPDT 开关功能:ON - ON - ON 电流额定值: 电压额定值 AC:20 V 电压额定值 DC:20 V 功率额定值:0.4 VA 端接类型:V-Bracket 安装风格: 端子密封:Epoxy 触点电镀:Gold 照明:Not Illuminated |
发布紧急采购，3分钟左右您将得到回复。