- 您现在的位置：买卖IC网 > PDF目录98143 > ST52F513G3B6 (STMICROELECTRONICS) 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PDIP28 PDF资料下载
参数资料
| 型号： | ST52F513G3B6 |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PDIP28 |
| 封装： | PLASTIC, DIP-28 |
| 文件页数： | 35/106页 |
| 文件大小： | 1340K |
| 代理商： | ST52F513G3B6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页当前第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页
A similar procedure can be used to write a single
block:
1.
The
SetPage command is sent, followed by
the page number where the data should be
written
2.
The
IncBlock command is sent as many times
as the block number inside the page (for ex-
ample: to address the block 3 the
IncBlock
must be sent 3 times)
3.
The
WriteBlock command is sent followed by
the 32 data bytes to be written.
4.
After the 32th byte is sent, the device holds
the SCL line low until all the data are not
stored in the memory (about 4.5 ms: 2 ms for
erasing and 2.5 for writing: the same time for
a single byte)
The procedures described previously can be
repeated as many time as needed, without exiting
from Programming Mode or re-sending the Slave
Address again.
The commands ByteErase and BlockErase, used
instead of ByteWrite and BlockWrite, erase (put all
bit to 0) the specified memory location or block.
4.2.4 Option Bytes Programming. The
Option
Byte addresses cannot be accessed with a
sequential procedure like the one described in
Actually,
the
pointers
are
automatically incremented up to the last block or
address in page 31. A further increment sets all the
pointers to 0.
The Option Byte addresses (located at page 48,
block 0, addresses 0-7) must be accessed with a
direct addressing procedure as the one described
If the Fast Programming procedure is used, it must
be followed by a Random Block Writing procedure
to program the Option Bytes. The other 24 bytes of
the block can be written with dummy or user
values. The blocks 0, 1, 2 and 3 of Page 48 can be
used for writing data as well (see Section 4.5) and
for locking the device (see Section 4.4).
Figure 4.2 Programming Procedures
Fast Programming Procedure
Random Byte Writing Procedure
Random Block Writing Procedure
Option Byte Writing Procedure
S=Start, P=Stop, A=Acknowledge, NA=Non-acknowledge
From Slave to Master
From Master to Slave
S 10100000
A
00000000
A
GlobalErase
A
FastBlockWrite
A
Data0
A
.....
Data31
A
IncBlock
A
FastBlockWrite
A
.....
Data31
A
.....
Data31
AP
.....
SetPage
A
Page Address
A
ByteWrite
A
Byte Address
AData
A
Command
.....
SetPage
A
Page Address
A
IncBlock
A
.....
IncBlock
A
BlockWrite
A
Data0
A
.....
Data31
A
Command
.....
SetPage
A
00110000
A
WriteBlock
A
Option Byte 0
A
.....
Option Byte 7
A
.....
Dummy 0
A
.....
Dummy 23
AP
相关PDF资料 |
PDF描述 |
|---|---|
| ST52F513Y1B6 | 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PDIP16 |
| ST52F513Y2B6 | 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PDIP16 |
| ST52F510Y3B6 | 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PDIP16 |
| ST52F514Y2B6 | 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PDIP16 |
| ST52T430K3B6 | 8-BIT, OTPROM, 20 MHz, MICROCONTROLLER, PDIP32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST52F513GMB6 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT INTELLIGENT CONTROLLER UNIT ICU Two Timer/PWMs, ADC, I2C, SPI, SCI |
| ST52F513GMM6 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT INTELLIGENT CONTROLLER UNIT ICU Two Timer/PWMs, ADC, I2C, SPI, SCI |
| ST52F513Y3M6 | 制造商:STMicroelectronics 功能描述: |
| ST52F513YMM6 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT INTELLIGENT CONTROLLER UNIT ICU Two Timer/PWMs, ADC, I2C, SPI, SCI |
| ST52F514 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT INTELLIGENT CONTROLLER UNIT ICU Two Timer/PWMs, ADC, I2C, SPI, SCI |
发布紧急采购，3分钟左右您将得到回复。