参数资料
型号: ST6240BQ6/XXX
厂商: STMICROELECTRONICS
元件分类: 微控制器/微处理器
英文描述: 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP80
封装: PLASTIC, QFP-80
文件页数: 20/73页
文件大小: 1963K
代理商: ST6240BQ6/XXX
Obsolete
Product(s)
- Obsolete
Product(s)
Obsolete
Product(s)
- Obsolete
Product(s)
27/73
ST62T40B/E40B
INTERRUPTS (Cont’d)
3.4.2 Interrupt Procedure
The interrupt procedure is very similar to a call pro-
cedure, indeed the user can consider the interrupt
as an asynchronous call procedure. As this is an
asynchronous event, the user cannot know the
context and the time at which it occurred. As a re-
sult, the user should save all Data space registers
which may be used within the interrupt routines.
There are separate sets of processor flags for nor-
mal, interrupt and non-maskable interrupt modes,
which are automatically switched and so do not
need to be saved.
The following list summarizes the interrupt proce-
dure:
MCU
– The interrupt is detected.
– The C and Z flags are replaced by the interrupt
flags (or by the NMI flags).
– The PC contents are stored in the first level of
the stack.
– The normal interrupt lines are inhibited (NMI still
active).
– The first internal latch is cleared.
– The associated interrupt vector is loaded in the PC.
WARNING: In some circumstances, when a
maskable interrupt occurs while the ST6 core is in
NORMAL mode and especially during the execu-
tion of an "ldi IOR, 00h" instruction (disabling all
maskable interrupts): if the interrupt arrives during
the first 3 cycles of the "ldi" instruction (which is a
4-cycle instruction) the core will switch to interrupt
mode BUT the flags CN and ZN will NOT switch to
the interrupt pair CI and ZI.
User
– User selected registers are saved within the in-
terrupt service routine (normally on a software
stack).
– The source of the interrupt is found by polling the
interrupt flags (if more than one source is associ-
ated with the same vector).
– The interrupt is serviced.
– Return from interrupt (RETI)
MCU
– Automatically the MCU switches back to the nor-
mal flag set (or the interrupt flag set) and pops
the previous PC value from the stack.
The interrupt routine usually begins by the identify-
ing the device which generated the interrupt re-
quest (by polling). The user should save the regis-
ters which are used within the interrupt routine in a
software stack. After the RETI instruction is exe-
cuted, the MCU returns to the main routine.
Figure 16. Interrupt Processing Flow Chart
INSTRUCTION
FETCH
INSTRUCTION
EXECUTE
INSTRUCTION
WAS
THE INSTRUCTION
A RETI
?
CLEAR
INTERRUPT MASK
SELECT
PROGRAM FLAGS
"POP"
THE STACKED PC
?
CHECK IF THERE IS
AN INTERRUPT REQUEST
AND INTERRUPT MASK
SELECT
INTERNAL MODE FLAG
PUSH THE
PC INTO THE STACK
LOAD PC FROM
INTERRUPT VECTOR
(FFC/FFD)
SET
INTERRUPT MASK
NO
YES
IS THE CORE
ALREADY IN
NORMAL MODE?
VA000014
YES
NO
YES
27
相关PDF资料
PDF描述
ST6242BQ1/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP64
ST6246BB6/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP56
ST6260BB6 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP20
ST6294B8/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP28
ST62T94B8 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDIP28
相关代理商/技术参数
参数描述
ST6240-P/QFP 功能描述:插座和适配器 ST62 P/QFP Adaptor RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x
ST6240Q1/XX 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller
ST6240Q6/XX 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller
ST6242 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT OTP/EPROM MCU WITH LCD DRIVER, EEPROM AND A/D CONVERTER
ST6242B 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-BIT MICROCONTROLLER ( MCU ) WITH OTP. ROM. FASTROM. EPROM. LCD DRIVER. EEPROM. A/D CONVERTER AND 64 PINS