- 您现在的位置：买卖IC网 > PDF目录98143 > ST6246BB6/XXX (STMICROELECTRONICS) 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP56 PDF资料下载
参数资料
| 型号： | ST6246BB6/XXX |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP56 |
| 封装： | 0.600 INCH, PLASTIC, SDIP-56 |
| 文件页数： | 39/73页 |
| 文件大小： | 1806K |
| 代理商： | ST6246BB6/XXX |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页当前第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页
Obsolete
Product(s)
- Obsolete
Product(s)
Obsolete
Product(s)
- Obsolete
Product(s)
44/73
ST62T46B/E46B
A/D CONVERTER (Cont’d)
Since the ADC is on the same chip as the micro-
processor, the user should not switch heavily load-
ed output signals during conversion, if high preci-
sion is required. Such switching will affect the sup-
ply voltages used as analog references.
The accuracy of the conversion depends on the
quality of the power supplies (VDD and VSS). The
user must take special care to ensure a well regu-
lated reference voltage is present on the VDD and
VSS pins (power supply voltage variations must be
less than 5V/ms). This implies, in particular, that a
suitable decoupling capacitor is used at the VDD
pin.
The converter resolution is given by::
The Input voltage (Ain) which is to be converted
must be constant for 1s before conversion and
remain constant during conversion.
Conversion resolution can be improved if the pow-
er supply voltage (VDD) to the microcontroller is
lowered.
In order to optimise conversion resolution, the user
can configure the microcontroller in WAIT mode,
because this mode minimises noise disturbances
and power supply variations due to output switch-
ing. Nevertheless, the WAIT instruction should be
executed as soon as possible after the beginning
of the conversion, because execution of the WAIT
instruction may cause a small variation of the VDD
voltage. The negative effect of this variation is min-
imized at the beginning of the conversion when the
converter is less sensitive, rather than at the end
of conversion, when the less significant bits are
determined.
The best configuration, from an accuracy stand-
point, is WAIT mode with the Timer stopped. In-
deed, only the ADC peripheral and the oscillator
are then still working. The MCU must be woken up
from WAIT mode by the ADC interrupt at the end
of the conversion. It should be noted that waking
up the microcontroller could also be done using
the Timer interrupt, but in this case the Timer will
be working and the resulting noise could affect
conversion accuracy.
A/D Converter Control Register (ADCR)
Address: 0D1h
—
Read/Write
Bit 7 = EAI: Enable A/D Interrupt. If this bit is set to
“1” the A/D interrupt is enabled, when EAI=0 the
interrupt is disabled.
Bit 6 = EOC: End of conversion. Read Only. This
read only bit indicates when a conversion has
been completed. This bit is automatically reset to
“0” when the STA bit is written. If the user is using
the interrupt option then this bit can be used as an
interrupt pending bit. Data in the data conversion
register are valid only when this bit is set to “1”.
Bit 5 = STA: Start of Conversion. Write Only. Writ-
ing a “1” to this bit will start a conversion on the se-
lected channel and automatically reset to “0” the
EOC bit. If the bit is set again when a conversion is
in progress, the present conversion is stopped and
a new one will take place. This bit is write only, any
attempt to read it will show a logical zero.
Bit 4 = PDS: Power Down Selection. This bit acti-
vates the A/D converter if set to “1”. Writing a “0” to
this bit will put the ADC in power down mode (idle
mode).
Bit 3-0 = D3-D0. Not used
A/D Converter Data Register (ADR)
Address: 0D0h
—
Read only
Bit 7-0 = D7-D0: 8 Bit A/D Conversion Result.
V
DD
V
SS
–
256
----------------------------
70
EAI
EOC
STA
PDS
D3
D2
D1
D0
70
D7
D6
D5
D4
D3
D2
D1
D0
相关PDF资料 |
PDF描述 |
|---|---|
| ST6260BB6 | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP20 |
| ST6294B8/XXX | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP28 |
| ST62T94B8 | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDIP28 |
| ST62E85BG1 | 8-BIT, UVPROM, 8 MHz, MICROCONTROLLER, CQFP80 |
| ST62P35BQ3/XXX | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP52 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST6246B-EMU2 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:REAL TIME EMULATION DEVELOPMENT TOOLS FOR ST6 MCU FAMILY |
| ST6246-P/QFP | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:REAL TIME EMULATION DEVELOPMENT TOOLS FOR ST6 MCU FAMILY |
| ST6-24B20 | 功能描述:电源变压器 SPLIT BOBBIN HORZ MOUNT XFMR RoHS:否 制造商:Triad Magnetics 功率额定值:12 VA 初级电压额定值:115 V / 230 V 次级电压额定值:12 V / 24 V 安装风格:SMD/SMT 一次绕组:Dual Primary Winding 二次绕组:Dual Secondary Winding 长度:2.5 in 宽度:2 in 高度:1.062 in |
| ST624OB-EMU2 | 制造商:STMicroelectronics 功能描述:ST62 EMULATOR |
| ST624X | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8/16-Bit Micros |
发布紧急采购，3分钟左右您将得到回复。