参数资料
型号: ST62E85BG1
厂商: STMICROELECTRONICS
元件分类: 微控制器/微处理器
英文描述: 8-BIT, UVPROM, 8 MHz, MICROCONTROLLER, CQFP80
封装: CERAMIC, QFP-80
文件页数: 43/78页
文件大小: 868K
代理商: ST62E85BG1
Obsolete
Product(s)
- Obsolete
Product(s)
48/78
ST62T85B/E85B
4.4.2 CLOCK GENERATION
The UART contains a built-in divider of the MCU
internal clock for most common Baud Rates as
shown in Table 19. Other baud rate values can be
calculated from the chosen oscillator frequency di-
vided by the Divisor value shown.
The divided clock provides a frequency that is 8
times the desired baud rate. This allows the Data
reception mechanism to provide a 2 to 1 majority
voting system to determine the logic state of the
asynchronous incoming serial logic bit by taking 3
timed samples within the 8 time states.
The bits not sampled provide a buffer to compen-
sate for frequency offsets between sender and re-
ceiver.
4.4.3 DATA TRANSMISSION
Transmission is fixed to a format of one start bit,
nine data bits and one stop bit. The start and stop
bits are automatically generated by the UART. The
nine databits are under control of the user and are
flexible in use. Bits 0..7 are typically used as data
bits while bit 9 is typically used as parity, but can
also be a 9th data bit or an additional Stop bit. As
parity is not generated by the UART, it should be
calculated by program and inserted in the appro-
priate position of the data (i.e as bit 7 for 7-bit data,
with Bit 9 set to 1 giving two effective stop bits or
as the independent bit 9).
Figure 24. Data Sampling Points
The character options are summarised in the fol-
lowing table.
Table 18. Character Options
Bit 9 remains in the state programmed for consec-
utive transmissions until changed by the user or
until a character is received when the state of this
bit is changed to that of the incoming bit 9. The
recommended procedure is thus to set the value of
this bit before transmission is started.
Transmission is started by writing to the Data Reg-
ister (the Baud Rate and Bit 9 should be set before
this action). The UARTOE signal switches the out-
put multiplexer to the UART output and a start bit
is sent (a 0 for one bit time) followed by the 8 data
values (lsb first) and the value of the Bit9 bit. The
output is then set to 1 for a period of one bit time to
generate a Stop bit, and then the UARTOE signal
returns the TXD1 line to its alternate I/O function.
The end of transmission is flagged by setting
TXMT to 1 and an interrupt is generated if ena-
bled. The TXMT flag is reset by writing a 0 to the
bit position, it is also cleared automatically when a
new character is written to the Data Register.
TXMT can be set to 1 by software to generate a
software interrupt so care must be taken in manip-
ulating the Control Register.
Figure 25. Character Format
VR02010
1 BIT
0
1
2
345
6
7
8
SAMPLES
Start Bit
8 Data
1 Software Parity
1 Stop
Start Bit
9 Data
No Parity
1 Stop
Start Bit
8 Data
No Parity
2 Stop
Start Bit
7 Data
1 Software Parity
2 Stop
VR02012
POSITION
1
28
10
BIT
START
STOP
BIT
POSSIBLE
NEXT
CHARACTER
START
D0 D1
D7 D8
START OF DATA
9
48
相关PDF资料
PDF描述
ST62P35BQ3/XXX 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP52
ST62P35BQ6/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP52
ST62P35BQ1/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP52
ST6235BQ1/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP52
ST62P45BQ6/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP52
相关代理商/技术参数
参数描述
ST62E85G1 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller
ST62E8X-EPB 制造商:未知厂家 制造商全称:未知厂家 功能描述:EPROM PROGRAMMING BOARDS DATASHEET FOR ST62 FAMILY
ST62E8X-EPB/110 功能描述:程序设计器 - 基于处理器 ST62 EPROM Programmr RoHS:否 制造商:Olimex Ltd. 产品:Programmers 工具用于评估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口类型:USB 工作电源电压:1.8 V to 5.5 V
ST62E94F1 制造商:未知厂家 制造商全称:未知厂家 功能描述:Telecommunication IC
ST62EBF1 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller