参数资料
型号: ST62P35BQ3/XXX
厂商: STMICROELECTRONICS
元件分类: 微控制器/微处理器
英文描述: 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP52
封装: PLASTIC, QFP-52
文件页数: 8/82页
文件大小: 617K
代理商: ST62P35BQ3/XXX
16/82
ST62T35B/E35B
2 CENTRAL PROCESSING UNIT
2.1 INTRODUCTION
The CPU Core of ST6 devices is independent of
the I/O or Memory configuration. As such, it may be
thought of as an independent central processor
communicating with on-chip I/O, Memory and Pe-
ripherals via internal address, data, and control
buses. In-core communication is arranged as
shown in Figure 6; the controller being externally
linked to both the Reset and Oscillator circuits,
while the core is linked to the dedicated on-chip pe-
ripherals via the serial data bus and indirectly, for
interrupt purposes, through the control registers.
2.2 CPU REGISTERS
The ST6 Family CPU core features six registers and
three pairs of flags available to the programmer.
These are described in the following paragraphs.
Accumulator (A). The accumulator is an 8-bit
general purpose register used in all arithmetic cal-
culations, logical operations, and data manipula-
tions. The accumulator can be addressed in Data
space as a RAM location at address FFh. Thus
the ST6 can manipulate the accumulator just like
any other register in Data space.
Indirect Registers (X, Y). These two indirect reg-
isters are used as pointers to memory locations in
Data space. They are used in the register-indirect
addressing mode. These registers can be ad-
dressed in the data space as RAM locations at ad-
dresses 80h (X) and 81h (Y). They can also be ac-
cessed with the direct, short direct, or bit direct ad-
dressing modes. Accordingly, the ST6 instruction
set can use the indirect registers as any other reg-
ister of the data space.
Short Direct Registers (V, W). These two regis-
ters are used to save a byte in short direct ad-
dressing mode. They can be addressed in Data
space as RAM locations at addresses 82h (V) and
83h (W). They can also be accessed using the di-
rect and bit direct addressing modes. Thus, the
ST6 instruction set can use the short direct regis-
ters as any other register of the data space.
Program Counter (PC). The program counter is a
12-bit register which contains the address of the
next ROM location to be processed by the core.
This ROM location may be an opcode, an oper-
and, or the address of an operand. The 12-bit
length allows the direct addressing of 4096 bytes
in Program space.
Figure 6ST6 Core Block Diagram
PROGRAM
RESET
OPCODE
FLAG
VALUES
2
CONTROLLER
FLAGS
ALU
A-DATA
B-DATA
ADDRESS/READ LINE
DATA SPACE
INTERRUP TS
DATA
RAM/EE PROM
DATA
ROM/EPROM
RESULTS TO DATA SPAC E (WRITE LINE)
ROM/EPROM
DEDICATION S
ACCUMULATOR
CONTROL
SIGNALS
OSCin
OSCout
ADDRESS
DECODER
256
12
Program Counter
and
6 LAYER STACK
0,01 TO 8MHz
VR01811
15
相关PDF资料
PDF描述
ST62P35BQ6/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP52
ST62P35BQ1/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP52
ST6235BQ1/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP52
ST62P45BQ6/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP52
ST62T03CM6E 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDSO16
相关代理商/技术参数
参数描述
ST62P52C 制造商:STMicroelectronics 功能描述:
ST62P62CM6/MOMTR 制造商:STMicroelectronics 功能描述:
ST62P62CM6/MPITR 制造商:STMicroelectronics 功能描述:
ST62P62CM6/MSATR 制造商:STMicroelectronics 功能描述:
ST62P62CN6/MMMTR 制造商:STMicroelectronics 功能描述: