收藏本站
参数资料
型号： ST62T65CM6
英文描述： IC-SM-8-BIT MCU 4K OTP
中文描述： 集成电路钐8位微控制器4K的检察官办公室
文件页数： 29/82页
文件大小： 870K
代理商： ST62T65CM6
29/82
ST62T18C/E18C
INTERRUPTS
(Cont’d)
3.4.2 Interrupt Procedure
The interrupt procedure is very similar to a call pro-
cedure, indeed the user can consider the interrupt
as an asynchronous call procedure. As this is an
asynchronous event, the user cannot know the
context and the time at which it occurred. As a re-
sult, the user should save all Data space registers
which may be used within the interrupt routines.
There are separate sets of processor flags for nor-
mal, interrupt and non-maskable interrupt modes,
which are automatically switched and so do not
need to be saved.
The following list summarizes the interrupt proce-
dure:
MCU
– The interrupt is detected.
– The C and Z flags are replaced by the interrupt
flags (or by the NMI flags).
– The PC contents are stored in the first level of
the stack.
– The normal interrupt lines are inhibited (NMI still
active).
– The first internal latch is cleared.
– The associated nterrupt vector s oaded n the PC.
WARNING:
In some circumstances, when a
maskable interrupt occurs while the ST6 core is in
NORMAL mode and especially during the execu-
tion of an "ldi IOR, 00h" instruction (disabling all
maskable interrupts): if the interrupt arrives during
the first 3 cycles of the "ldi" instruction (which is a
4-cycle instruction) the core will switch to interrupt
mode BUT the flags CN and ZN will NOT switch to
the interrupt pair CI and ZI.
User
– User selected registers are saved within the in-
terrupt service routine (normally on a software
stack).
– The source of the interrupt is found by polling the
interrupt flags (if more than one source is associ-
ated with the same vector).
– The interrupt is serviced.
– Return from interrupt (RETI)
MCU
– Automatically the MCU switches back to the nor-
mal flag set (or the interrupt flag set) and pops
the previous PC value from the stack.
The interrupt routine usually begins by the identify-
ing the device which generated the interrupt re-
quest (by polling). The user should save the regis-
ters which are used within the interrupt routine in a
software stack. After the RETI instruction is exe-
cuted, the MCU returns to the main routine.
Figure 20. Interrupt Processing Flow Chart
INSTRUCTION
FETCH
INSTRUCTION
EXECUTE
INSTRUCTION
TH WAS
A RETI
CLEAR
INTERRUPT MASK
SELECT
PROGRAM FLAGS
"POP"
THE STACKED PC
CHECK IF THERE IS
AN INTERRUPT REQUEST
AND INTERRUPT MASK
SELECT
INTERNAL MODE FLAG
PUSH THE
PC INTO THE STACK
LOAD PC FROM
INTERRUPT VECTOR
(FFC/FFD)
SET
INTERRUPT MASK
NO
NO
YES
IS THE CORE
ALREADY IN
NORMAL MODE
VA000014
YES
NO
YES
29
相关PDF资料
PDF描述
ST62T65CN6 IC-SM-8-BIT MCU 4K OTP
ST62T94B8 Telecommunication IC
ST62T94M8 Telecommunication IC
ST6228C 8-BIT MICROCONTROLLER ( MCU ) WITH OTP. ROM. FASTR A/D CONVERTER. 8-BIT AUTO-RELOAD TIMER. UART. OSG. SAFE RESET AND 28 PINS
ST62E28CF1 8-BIT MICROCONTROLLER ( MCU ) WITH OTP. ROM. FASTR A/D CONVERTER. 8-BIT AUTO-RELOAD TIMER. UART. OSG. SAFE RESET AND 28 PINS
相关代理商/技术参数
参数描述
ST62T65CM6 制造商:STMicroelectronics 功能描述:8BIT MCU OTP 4K+EEPROM SMD 62T65
ST62T65CN6 功能描述:8位微控制器 -MCU OTP EPROM 4K SPI RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ST62T80BQ6 功能描述:8位微控制器 -MCU OTP EPROM 8K SPI/UAR RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ST62T85BQ6 功能描述:8位微控制器 -MCU OTP EPROM 8K SPI/UAR RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ST63/69/23 制造商:Block 功能描述:Control panel transformer, 63VA, 230V
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*