参数资料
型号: ST62T94B8
英文描述: Telecommunication IC
中文描述: 通信集成电路
文件页数: 14/82页
文件大小: 870K
代理商: ST62T94B8
14/82
ST62T18C/E18C
2 CENTRAL PROCESSING UNIT
2.1 INTRODUCTION
The CPU Core of ST6 devices is independent of the
I/O or Memory configuration. As such, it may be
thought of as an independent central processor
communicating with on-chip I/O, Memory and Pe-
ripherals via internal address, data, and control
buses. In-core communication is arranged as
shown in
Figure 6
; the controller being externally
linked to both the Reset and Oscillator circuits,
while the core is linked to the dedicated on-chip pe-
ripherals via the serial data bus and indirectly, for
interrupt purposes, through the control registers.
2.2 CPU REGISTERS
The ST6 Family CPU core features six registers and
three pairs of flags available to the programmer.
These are described in the following paragraphs.
Accumulator (A)
. The accumulator is an 8-bit
general purpose register used in all arithmetic cal-
culations, logical operations, and data manipula-
tions. The accumulator can be addressed in Data
space as a RAM location at address FFh. Thus the
ST6 can manipulate the accumulator just like any
other register in Data space.
Indirect Registers (X, Y).
These two indirect reg-
isters are used as pointers to memory locations in
Data space. They are used in the register-indirect
addressing mode. These registers can be ad-
dressed in the data space as RAM locations at ad-
dresses 80h (X) and 81h (Y). They can also be ac-
cessed with the direct, short direct, or bit direct ad-
dressing modes. Accordingly, the ST6 instruction
set can use the indirect registers as any other reg-
ister of the data space.
Short Direct Registers (V, W).
These two regis-
ters are used to save a byte in short direct ad-
dressing mode. They can be addressed in Data
space as RAM locations at addresses 82h (V) and
83h (W). They can also be accessed using the di-
rect and bit direct addressing modes. Thus, the
ST6 instruction set can use the short direct regis-
ters as any other register of the data space.
Program Counter (PC). The program counter is a
12-bit register which contains the address of the
next ROM location to be processed by the core.
This ROM location may be an opcode, an oper-
and, or the address of an operand. The 12-bit
length allows the direct addressing of 4096 bytes
in Program space.
Figure 6. ST6 Core Block Diagram
PROGRAM
RESET
OPCODE
FLAG
VALUES
2
CONTROLLER
FLAGS
ALU
A-DATA
B-DATA
ADDRESS/READ LINE
DATA SPACE
INTERRUPTS
DATA
RAM/EEPROM
DATA
ROM/EPROM
RESULTS TO DATA SPACE (WRITE LINE)
ROM/EPROM
DEDICATIONS
ACCUMULATOR
CONTROL
SIGNALS
OSCin
OSCout
ADDRESS
DECODER
256
12
Program Counter
and
6 LAYER STACK
0,01 TO 8MHz
VR01811
14
相关PDF资料
PDF描述
ST62T94M8 Telecommunication IC
ST6228C 8-BIT MICROCONTROLLER ( MCU ) WITH OTP. ROM. FASTR A/D CONVERTER. 8-BIT AUTO-RELOAD TIMER. UART. OSG. SAFE RESET AND 28 PINS
ST62E28CF1 8-BIT MICROCONTROLLER ( MCU ) WITH OTP. ROM. FASTR A/D CONVERTER. 8-BIT AUTO-RELOAD TIMER. UART. OSG. SAFE RESET AND 28 PINS
ST62P28CB1 8-BIT MICROCONTROLLER ( MCU ) WITH OTP. ROM. FASTR A/D CONVERTER. 8-BIT AUTO-RELOAD TIMER. UART. OSG. SAFE RESET AND 28 PINS
ST62P28CB3 8-BIT MICROCONTROLLER ( MCU ) WITH OTP. ROM. FASTR A/D CONVERTER. 8-BIT AUTO-RELOAD TIMER. UART. OSG. SAFE RESET AND 28 PINS
相关代理商/技术参数
参数描述
ST63/69/23 制造商:Block 功能描述:Control panel transformer, 63VA, 230V
ST6-30 制造商:SUPERWORLD 制造商全称:Superworld Electronics 功能描述:POWER TRANSFORMER
ST630/69/23 制造商:Block USA Inc. 功能描述:Control panel transformer, 630VA, 230V
ST6306 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller
ST6307 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller