- 您现在的位置：买卖IC网 > PDF目录372305 > ST62T94M8 Telecommunication IC PDF资料下载
参数资料
| 型号： | ST62T94M8 |
| 英文描述： | Telecommunication IC |
| 中文描述： | 通信集成电路 |
| 文件页数： | 7/82页 |
| 文件大小： | 870K |
| 代理商： | ST62T94M8 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页
7/82
ST62T18C/E18C
1.2 PIN DESCRIPTIONS
V
and V
. Power is supplied to the MCU via
these two pins. V
is the power connection and
V
SS
is the ground connection.
OSCin and OSCout.
These pins are internally
connected to the on-chip oscillator circuit. A quartz
crystal, a ceramic resonator or an external clock
signal can be connected between these two pins.
The OSCin pin is the input pin, the OSCout pin is
the output pin.
RESET
. The active-low RESET pin is used to re-
start the microcontroller.
TEST/V
.
The TEST must be held at V
for nor-
mal operation. If TEST pin is connected to a
+12.5V level during the reset phase, the EPROM/
OTP programming Mode is entered.
NMI.
The NMI pin provides the capability for asyn-
chronous interruption, by applying an external non
maskable interrupt to the MCU. Schmitt trigger
characteristics. The user can select as option the
availability of an on-chip pull-up at this pin.
PA1-PA5.
These 5 lines are organised as one I/O
port (A). Each line may be configured under soft-
ware control as inputs with or without internal pull-
up resistors, input with interrupt generation and
pull-up resistor, open-drain or push-pull outputs.
PA3/ARTIMout and PA4/ARTIMin can be used re-
spectively as output and input pins for the embed-
ded 8-bit Auto-Reload Timer.
In addition,
PA1-PA5
can sink 20mA for direct LED
or TRIAC drive.
PB4...PB6.
These 3 lines are organised as one I/O
port (B). Each line may be configured under soft-
ware control as inputs with or without internal pull-
up resistors, input with interrupt generation and
pull-up resistor, open-drain or push-pull outputs,
analog inputs for the A/D converter.
PD4...PD7
. These 4 lines are organised as one I/O
port (portD). Each line may be configured under
software control as input with or without internal
pull-up resistor, input with interrupt generation and
pull-up resistor, analog input open-drain or push-
pull output. In addition, the pins PD5/TXD1 and
PD4/RXD1 can be used as UART output (PD5/
TXD1) or UART input (PD4/RXD1).
TIMER
. This is the TIMER 1 I/O pin. In input mode,
it is connected to the prescaler and acts as ex-
ternal timer clock or as control gate for the internal
timer clock. In output mode, the TIMER pin outputs
the data bit when a time-out occurs.The user can
select as option the availability of an on-chip pull-
up at this pin.
7
相关PDF资料 |
PDF描述 |
|---|---|
| ST6228C | 8-BIT MICROCONTROLLER ( MCU ) WITH OTP. ROM. FASTR A/D CONVERTER. 8-BIT AUTO-RELOAD TIMER. UART. OSG. SAFE RESET AND 28 PINS |
| ST62E28CF1 | 8-BIT MICROCONTROLLER ( MCU ) WITH OTP. ROM. FASTR A/D CONVERTER. 8-BIT AUTO-RELOAD TIMER. UART. OSG. SAFE RESET AND 28 PINS |
| ST62P28CB1 | 8-BIT MICROCONTROLLER ( MCU ) WITH OTP. ROM. FASTR A/D CONVERTER. 8-BIT AUTO-RELOAD TIMER. UART. OSG. SAFE RESET AND 28 PINS |
| ST62P28CB3 | 8-BIT MICROCONTROLLER ( MCU ) WITH OTP. ROM. FASTR A/D CONVERTER. 8-BIT AUTO-RELOAD TIMER. UART. OSG. SAFE RESET AND 28 PINS |
| ST62P28CB6 | 8-BIT MICROCONTROLLER ( MCU ) WITH OTP. ROM. FASTR A/D CONVERTER. 8-BIT AUTO-RELOAD TIMER. UART. OSG. SAFE RESET AND 28 PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST63/69/23 | 制造商:Block 功能描述:Control panel transformer, 63VA, 230V |
| ST6-30 | 制造商:SUPERWORLD 制造商全称:Superworld Electronics 功能描述:POWER TRANSFORMER |
| ST630/69/23 | 制造商:Block USA Inc. 功能描述:Control panel transformer, 630VA, 230V |
| ST6306 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller |
| ST6307 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller |
发布紧急采购，3分钟左右您将得到回复。