参数资料
型号: ST72311R9T3/XXX
厂商: STMICROELECTRONICS
元件分类: 微控制器/微处理器
英文描述: 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP64
封装: 14 X 14 MM, TQFP-64
文件页数: 130/152页
文件大小: 1909K
代理商: ST72311R9T3/XXX
ST72311R, ST72511R, ST72532R
79/152
10.5 SERIAL PERIPHERAL INTERFACE (SPI)
10.5.1 Introduction
The Serial Peripheral Interface (SPI) allows full-
duplex, synchronous, serial communication with
external devices. An SPI system may consist of a
master and one or more slaves or a system in
which devices may be either masters or slaves.
The SPI is normally used for communication be-
tween the microcontroller and external peripherals
or another microcontroller.
Refer to the Pin Description chapter for the device-
specific pin-out.
10.5.2 Main Features
s
Full duplex, three-wire synchronous transfers
s
Master or slave operation
s
Four master mode frequencies
s
Maximum slave mode frequency = fCPU/4.
s
Four programmable master bit rates
s
Programmable clock polarity and phase
s
End of transfer interrupt flag
s
Write collision flag protection
s
Master mode fault protection capability.
10.5.3 General description
The SPI is connected to external devices through
4 alternate pins:
– MISO: Master In Slave Out pin
– MOSI: Master Out Slave In pin
– SCK: Serial Clock pin
–SS: Slave select pin
A basic example of interconnections between a
single master and a single slave is illustrated on
Figure 46.
The MOSI pins are connected together as are
MISO pins. In this way data is transferred serially
between master and slave (most significant bit
first).
When the master device transmits data to a slave
device via MOSI pin, the slave device responds by
sending data to the master device via the MISO
pin. This implies full duplex transmission with both
data out and data in synchronized with the same
clock signal (which is provided by the master de-
vice via the SCK pin).
Thus, the byte transmitted is replaced by the byte
received and eliminates the need for separate
transmit-empty and receiver-full bits. A status flag
is used to indicate that the I/O operation is com-
plete.
Four possible data/clock timing relationships may
be chosen (see Figure 49) but master and slave
must be programmed with the same timing mode.
Figure 46. Serial Peripheral Interface Master/Slave
8-BIT SHIFT REGISTER
SPI
CLOCK
GENERATOR
8-BIT SHIFT REGISTER
MISO
MOSI
MISO
SCK
SLAVE
MASTER
SS
+5V
MSBit
LSBit
MSBit
LSBit
相关PDF资料
PDF描述
ST72T311R7T7 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP64
ST72T532R4T6 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP64
ST72311R7T6/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP64
ST72311R7T3/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP64
ST72T511R6T7 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP64
相关代理商/技术参数
参数描述
ST72311R9T6 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, EEPROM, ADC, 16-BIT TIMERS, 8-BIT PWM ART, SPI, SCI, CAN INTERFACES
ST72311R9T6/XXX 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller
ST72311R9T6S 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, EEPROM, ADC, 16-BIT TIMERS, 8-BIT PWM ART, SPI, SCI, CAN INTERFACES
ST72311R9T6S/XXX 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller
ST72311R9T7 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, EEPROM, ADC, 16-BIT TIMERS, 8-BIT PWM ART, SPI, SCI, CAN INTERFACES