参数资料
| 型号： | ST78C36CJ44TR-F |
| 厂商： | Exar Corporation |
| 文件页数： | 23/27页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 16B 44PLCC |
| 标准包装： | 500 |
| 特点： | * |
| FIFO's： | 16 字节 |
| 规程： | 打印机 |
| 电源电压： | 5V |
| 带并行端口： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-LCC（J 形引线） |
| 供应商设备封装： | 44-PLCC（16.59x16.59） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页
ST78C36/36A
5
REV. 5.1.0
ECP/EPP PARALLEL PRINTER PORT WITH 16-BYTE FIFO
1.0 OVERVIEW
This device is designed around the Hewlett Packard/Microsoft specification for Extended Capabilities Port
Protocol with “ECR mode 100” defined as Enhanced Parallel Port (EPP) mode. The internal timing engines
were designed around a 24 MHz reference, which can be supplied from an external source or by the built-in
oscillator circuit (ST78C36ACJ and ST78C36CQ64 only) with an appropriate crystal.
At system RESET, the device defaults to standard IBM PC compatible Centronics printer mode (output only).
The bi-directional PS/2, EPP, and ECP modes can only be activated by programming the ECR mode field (this
requires address bit A10 = 1, which is outside the normal ISA I/O space).
Optional capabilities of the ECP specification are set as follows:
■ ECP defined interrupts are pulsed, LOW true (Centronics -ACK is non-pulsed, LOW true).
■ PWord size is forced to 1 byte.
■ There is 1 byte in the transmitter that does not affect the FIFO full bit (ECP modes).
■ RLE compression is not supported in hardware.
■ IRQ channel is selectable as 5, 7, or 9 (ST78C36CQ64 only).
■ DMA channel is selectable as 1, 2, or 3 (ST78C36CQ64 only).
■ FIFO THRESHOLD is set at 8 (used only for non-DMA access to the FIFO).
DATA
000
R/W
000, 001
Data Register
ECP-AFIFO
000
W
011
ECP FIFO (Address)
DSR
001
R
All
Status Register
DCR
002
R/W
All
Control Register
EPP-APort
003
R/W
100
EPP Port (Address)
EPP-DPort
004 - 007
R/W
100
EPP Port (Data)
C-FIFO
400
W
010
Parallel Port Data FIFO
ECP-DFIFO
400
R/W
011
ECP FIFO (Data)
T-FIFO
400
R/W
110
Test FIFO
Cnfg-A
400
R
111
Configuration Register A
Cnfg-B
401
R/W
111
Configuration Register B
ECR
402
R/W
All
Extended Control Register
VCC
44
16, 56
Pwr
Power Supply (+5V).
GND
23,30
15, 25,
37, 48,
64
Pwr
Supply Ground.
PORT
ADDRESS
R/W
MODE
FUNCTION
PIN DESCRIPTION
NAME
44-PLCC
PIN
#
64-LQFP
PIN
#
TYPE
DESCRIPTION
相关PDF资料 |
PDF描述 |
|---|---|
| XR16L2550IMTR-F | IC UART FIFO 16B DUAL 48TQFP |
| XR16M780IL32-F | IC UART FIFO 64B 32QFN |
| XR68M752IL32TR-F | IC UART FIFO 64B DUAL 32QFN |
| ATMEGA168-15AT | MCU AVR 16K FLASH 15MHZ 32-TQFP |
| ST16C450CQ48TR-F | IC UART SINGLE 48TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST78C36CQ-0A-EVB | 功能描述:界面开发工具 Supports 78C36 64 ld TQFP, ISA Interface RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| ST78C36CQ64 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| ST78C36CQ64-F | 功能描述:接口 - 专用 UART RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| ST78L05 | 制造商:SEMTECH_ELEC 制造商全称:SEMTECH ELECTRONICS LTD. 功能描述:3-Terminal positive voltage regulator |
| ST78L05U | 制造商:SEMTECH_ELEC 制造商全称:SEMTECH ELECTRONICS LTD. 功能描述:3-Terminal Positive Voltage Regulator |
发布紧急采购，3分钟左右您将得到回复。