参数资料
型号: ST7FL09Y0MATRE
厂商: STMICROELECTRONICS
元件分类: 微控制器/微处理器
英文描述: 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PDSO16
封装: 0.150 INCH, ROHS COMPLIANT, PLASTIC, SOP-16
文件页数: 63/104页
文件大小: 2151K
代理商: ST7FL09Y0MATRE
Obsolete
Product(s)
- Obsolete
Product(s)
ST7L05, ST7L09
61/104
SERIAL PERIPHERAL INTERFACE (Cont’d)
11.3.8 Register Description
CONTROL REGISTER (SPICR)
Read/Write
Reset Value: 0000 xxxx (0xh)
Bit 7 = SPIE Serial Peripheral Interrupt Enable
This bit is set and cleared by software.
0: Interrupt is inhibited
1: An SPI interrupt is generated whenever SPIF =
1, MODF = 1 or OVR = 1 in the SPICSR register
Bit 6 = SPE Serial Peripheral Output Enable
This bit is set and cleared by software. It is also
cleared by hardware when, in master mode,
(MODF)). The SPE bit is cleared by reset, so the
SPI peripheral is not initially connected to the ex-
ternal pins.
0: I/O pins free for general purpose I/O
1: SPI I/O pin alternate functions enabled
Bit 5 = SPR2 Divider Enable
This bit is set and cleared by software and is
cleared by reset. It is used with the SPR[1:0] bits to
set the baud rate. Refer to Table 15 SPI Master
0: Divider by 2 enabled
1: Divider by 2 disabled
Note: This bit has no effect in slave mode.
Bit 4 = MSTR Master Mode
This bit is set and cleared by software. It is also
cleared by hardware when, in master mode,
0: Slave mode
1: Master mode. The function of the SCK pin
changes from an input to an output and the func-
tions of the MISO and MOSI pins are reversed.
Bit 3 = CPOL Clock Polarity
This bit is set and cleared by software. This bit de-
termines the idle state of the serial Clock. The
CPOL bit affects both the master and slave
modes.
0: SCK pin has a low level idle state
1: SCK pin has a high level idle state
Note: If CPOL is changed at the communication
byte boundaries, the SPI must be disabled by re-
setting the SPE bit.
Bit 2 = CPHA Clock Phase
This bit is set and cleared by software.
0: The first clock transition is the first data capture
edge.
1: The second clock transition is the first capture
edge.
Note: The slave must have the same CPOL and
CPHA settings as the master.
Bits 1:0 = SPR[1:0] Serial Clock Frequency
These bits are set and cleared by software. Used
with the SPR2 bit, they select the baud rate of the
SPI serial clock SCK output by the SPI in master
mode.
Note: These 2 bits have no effect in slave mode.
Table 15. SPI Master mode SCK Frequency
70
SPIE
SPE
SPR2
MSTR
CPOL
CPHA
SPR1
SPR0
Serial Clock
SPR2
SPR1
SPR0
fCPU/4
1
0
fCPU/8
0
fCPU/16
0
1
fCPU/32
1
0
fCPU/64
0
1
0
fCPU/128
0
1
相关PDF资料
PDF描述
ST7FL09Y0MBE 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PDSO16
ST7FL05Y0MAE 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PDSO16
ST7FL05Y0MBTRE 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PDSO16
ST7FL05Y0MATRE 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PDSO16
ST7FLCD1G9M1 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PDSO28
相关代理商/技术参数
参数描述
ST7FL09Y0MB 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-bit MCU for automotive with single voltage Flash memory, data EEPROM, ADC, timers, SPI
ST7FL09Y0MBE 制造商:STMicroelectronics 功能描述:
ST7FL15F1MAE 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-bit MCU for automotive with single voltage Flash/ROM memory, data EEPROM, ADC, 5 timers, SPI
ST7FL15F1MARE 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-bit MCU for automotive with single voltage Flash/ROM memory, data EEPROM, ADC, 5 timers, SPI
ST7FL15F1MATRE 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-bit MCU for automotive with single voltage Flash/ROM memory, data EEPROM, ADC, 5 timers, SPI