- 您现在的位置：买卖IC网 > PDF目录243484 > ST7FLITEUS5M6 (STMICROELECTRONICS) 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO8 PDF资料下载
参数资料
| 型号： | ST7FLITEUS5M6 |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO8 |
| 封装： | 0.150 INCH, LEAD FREE, PLASTIC, SOP-8 |
| 文件页数： | 14/108页 |
| 文件大小： | 1957K |
| 代理商： | ST7FLITEUS5M6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页
ST7LITEUSx
13/108
FLASH PROGRAM MEMORY (Cont’d)
5. A serial resistor must be connected to ICC con-
nector pin 6 in order to prevent contention on PA3/
RESET pin. Contention may occur if a tool forces a
state on RESET pin while PA3 pin forces the op-
posite state in output mode. The resistor value is
defined to limit the current below 2mA at 5V. If PA3
is used as output push-pull, then the application
must be switched off to allow the tool to take con-
trol of the RESET pin (PA3). To allow the program-
ming tool to drive the RESET pin below VIL, spe-
cial care must also be taken when a pull-up is
placed on PA3 for application reasons.
Caution: During normal operation, ICCCLK pin
must be pulled- up, internally or externally (exter-
nal pull-up of 10k mandatory in noisy environ-
ment). This is to avoid entering ICC mode unex-
pectedly during a reset. In the application, even if
the pin is configured as output, any reset will put it
back in input pull-up.
4.5 Memory Protection
There are two different types of memory protec-
tion: read-out protection and Write/Erase Protec-
tion which can be applied individually.
4.5.1 Read-out Protection
Readout protection, when selected provides a pro-
tection against program memory content extrac-
tion and against write access to Flash memory.
Even if no protection can be considered as totally
unbreakable, the feature provides a very high level
of protection for a general purpose microcontroller.
Program memory is protected.
In flash devices, this protection is removed by re-
programming the option. In this case, program
memory is automatically erased, and the device
can be reprogrammed.
Read-out protection selection depends on the de-
vice type:
– In Flash devices it is enabled and removed
through the FMP_R bit in the option byte.
– In ROM devices it is enabled by mask option
specified in the Option List.
4.5.2 Flash Write/Erase Protection
Write/erase protection, when set, makes it impos-
sible to both overwrite and erase program memo-
ry. Its purpose is to provide advanced security to
applications and prevent any change being made
to the memory content.
Warning: Once set, Write/erase protection can
never be removed. A write-protected flash device
is no longer reprogrammable.
Write/erase protection is enabled through the
FMP_W bit in the option byte.
4.6 Related Documentation
For details on Flash programming and ICC proto-
col, refer to the ST7 Flash Programming Refer-
ence Manual and to the ST7 ICC Protocol Refer-
ence Manual
.
4.7 Register Description
FLASH CONTROL/STATUS REGISTER (FCSR)
Read/Write
Reset Value: 000 0000 (00h)
1st RASS Key: 0101 0110 (56h)
2nd RASS Key: 1010 1110 (AEh)
Note: This register is reserved for programming
using ICP, IAP or other programming methods. It
controls the XFlash programming and erasing op-
erations.
When an EPB or another programming tool is
used (in socket or ICP mode), the RASS keys are
sent automatically.
Table 3. FLASH Register Map and Reset Values
70
00
000
OPT
LAT
PGM
Address
(Hex.)
Register
Label
76543
210
002Fh
FCSR
Reset Value
00000
OPT
0
LAT
0
PGM
0
1
相关PDF资料 |
PDF描述 |
|---|---|
| ST7PLITEUS2M6 | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO8 |
| SAF-XC2299H-200F80L | 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP176 |
| SAF-XC2388C-136F80L | 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP144 |
| SAH-XC2299H-200F80L | 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP176 |
| SAK-XC2289H-200F80L | 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP144 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST7FLITEUS5M6TR | 功能描述:8位微控制器 -MCU ST7ULTRALITE 8B MCU SINGLE Vltg FLASH RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| ST7FLITEUS5U3 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-bit MCU with single voltage Flash memory, ADC, timers |
| ST7FLITEUS5U3TR | 功能描述:8位微控制器 -MCU 8 BITS MICROCONTR RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| ST7FLITEUS5U6 | 制造商:STMicroelectronics 功能描述:8 BITS MICROCONTR - Bulk |
| ST7FLITEUS5U6/TR | 功能描述:MCU 8BIT 1KB FLASH 128KB 8-DFN RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:ST7 标准包装:96 系列:PIC® 16F 核心处理器:PIC 芯体尺寸:8-位 速度:20MHz 连通性:I²C，SPI 外围设备:欠压检测/复位，POR，PWM，WDT 输入/输出数:11 程序存储器容量:3.5KB（2K x 14） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:128 x 8 电压 - 电源 (Vcc/Vdd):2.3 V ~ 5.5 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。