参数资料
型号: ST7FLU05MAE
厂商: STMICROELECTRONICS
元件分类: 微控制器/微处理器
英文描述: 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO8
封装: 0.150 INCH, LEAD FREE, PLASTIC, SOP-8
文件页数: 36/124页
文件大小: 2186K
代理商: ST7FLU05MAE
Obsolete
Product(s)
- Obsolete
Product(s)
ST7LUS5, ST7LU05, ST7LU09
Flash program memory
19/124
Depending on the ICP driver code downloaded in RAM, Flash memory programming can be
fully customized (number of bytes to program, program locations, or selection of the serial
communication interface for downloading).
4.3.2
In-application programming (IAP)
This mode uses an IAP driver program previously programmed in Sector 0 by the user (in
ICP mode).
This mode is fully controlled by user software. This allows it to be adapted to the user
application (user-defined strategy for entering programming mode or choice of
communications protocol used to fetch the data to be stored, etc.).
IAP mode can be used to program any memory areas except Sector 0, which is write/erase
protected to allow recovery in case errors occur during the programming operation.
4.4
ICC interface
ICP needs a minimum of 4 and up to 6 pins to be connected to the programming tool. These
pins are:
RESET:
Device reset
VSS:
Device power supply ground
ICCCLK:
ICC output serial clock pin(b)
ICCDATA: ICC input serial data pin
CLKIN:
Main clock input for external source
VDD:
Application board power supply(c)
b.
If the ICCCLK or ICCDATA pins are only used as outputs in the application, no signal isolation is necessary. As
soon as the programming tool is plugged to the board, even if an ICC session is not in progress, the ICCCLK
and ICCDATA pins are not available for the application. If they are used as inputs by the application, isolation
such as a serial resistor has to be implemented in case another device forces the signal. Refer to the
programming tool documentation for recommended resistor values.
c.
The use of Pin 7 of the ICC connector depends on the programming tool architecture. This pin must be
connected when using most ST programming tools (it is used to monitor the application power supply). Please
refer to the programming tool manual.
相关PDF资料
PDF描述
ST7LNB0V2Y0M6 8-BIT, 8 MHz, MICROCONTROLLER, PDSO16
ST7LNB1Y0M6 8-BIT, EEPROM, 8 MHz, MICROCONTROLLER, PDSO16
ST7PL05Y0MB/XXXTRE 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO16
ST7PL05Y0MB 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO16
ST7PLITE05F0U6TR 8-BIT, MROM, 16 MHz, MICROCONTROLLER, QCC20
相关代理商/技术参数
参数描述
ST7FLU09MCE 制造商:STMicroelectronics 功能描述:
ST7FMC1K2B3 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-bit MCU with nested interrupts, Flash, 10-bit ADC, brushless motor control, five timers, SPI, LINSCI?
ST7FMC1K2B6 功能描述:8位微控制器 -MCU 8 BITS MICROCONTR RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ST7FMC1K2T3 功能描述:8位微控制器 -MCU ST7MC1/ST7MC2 8B MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ST7FMC1K2T6 功能描述:8位微控制器 -MCU 8K Flash 384 RAM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT