- 您现在的位置：买卖IC网 > PDF目录98148 > STLED316SMTR (STMICROELECTRONICS) 4 X 17 SEGMENTS SEGMENT LED DRVR AND DSPL CTLR, PDSO24 PDF资料下载
参数资料
| 型号： | STLED316SMTR |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 显示控制器 |
| 英文描述： | 4 X 17 SEGMENTS SEGMENT LED DRVR AND DSPL CTLR, PDSO24 |
| 封装： | ROHS COMPLIANT, SOP-24 |
| 文件页数： | 10/33页 |
| 文件大小： | 438K |
| 代理商： | STLED316SMTR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
Key matrix and key-input data storage ram
STLED316S
18/33
7
Key matrix and key-input data storage ram
During the key scan cycle all the grids are turned off. The first segments turn on is 64 s.
The key1 and key2 signals will be sampled after 60 s. The two signals latch into the
internal key buffer. The same applies for other segments.
This key buffer compares the data with the previous key status. If any changes are seen in
the buffer values, then the IRQ_N is asserted. The IRQ_N signal is active low (level). This
IRQ_N signal will be cleared at the end of reading the key buffer (end of byte transfer). The
key buffer must be completely read before the IRQ_N is cleared.
The key matrix is of 8 x 2 configuration, as shown below:
Figure 4.
Key matrix
The data of each key are stored as illustrated below, and are read by the appropriate read
command, starting from the least significant bit.
1st byte
2nd byte
The initial key buffer value is “00”. During operation, the buffer values will change depending
upon the values of the key-press.
KEY1
SEG1/KS1
SEG2/KS2
SEG3/KS3
SEG4/KS4
SEG5/KS5
SEG6/KS6
SEG7/KS7
SEG8/KS8
LSB
MSB
KEY2
SEG1/KS1
SEG2/KS2
SEG3/KS3
SEG4/KS4
SEG5/KS5
SEG6/KS6
SEG7/KS7
SEG8/KS8
LSB
MSB
相关PDF资料 |
PDF描述 |
|---|---|
| STM32F101C8T6 | 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, PQFP48 |
| STM32F101R6T6 | 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, PQFP64 |
| STM32F101VBT6 | 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, PQFP100 |
| STM32F101T6U6 | 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, QCC36 |
| STM32F101CBT6AXX | 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, PQFP48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| STLED325QTR | 功能描述:LED照明驱动器 I2C interfaced LED controller/driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| STLED32MAT-EVAL1 | 功能描述:BOARD EVALUATION FOR LED ARRAY RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| STLED524 | 功能描述:IC MATRIX LED DISPL DVR 56CSP 制造商:stmicroelectronics 系列:- 包装:剪切带（CT） 零件状态:有效 显示类型:LED 配置:点阵 接口:SPI 数字或字符:- 电流 - 电源:- 电压 - 电源:2.7 V ~ 5.5 V 工作温度:-30°C ~ 85°C 安装类型:表面贴装 封装/外壳:56-UFBGA，WLCSP 供应商器件封装:56-CSP（3.4x3.0） 标准包装:1 |
| ST-LEQ1 | 制造商:Radio Design Labs 功能描述:Use With Vca Loudne Equalizer 制造商:RADIO DESIGN LABS 功能描述:LOUDNESS EQUALIZER USE WITH VCA |
| STLGCA-1.024 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Crystal Oscillator |
发布紧急采购，3分钟左右您将得到回复。