参数资料
型号: STLED316SMTR
厂商: STMICROELECTRONICS
元件分类: 显示控制器
英文描述: 4 X 17 SEGMENTS SEGMENT LED DRVR AND DSPL CTLR, PDSO24
封装: ROHS COMPLIANT, SOP-24
文件页数: 9/33页
文件大小: 438K
代理商: STLED316SMTR
STLED316S
Key-scan & display cycle
17/33
6
Key-scan & display cycle
The display RAM stores the data transmitted from an external device to the STLED316S
through the serial interface. Refer to Section 9: Key-scanning and display timing on page 25
for a pictorial representation.
The grid and segment outputs are controlled by the display output module. The entire grid
will be turned off on channel 1/16 and 16/16 meaning that the first channel and last channel
are off. This is referred to as blanking time.
During the keyscan time (first cycle from timing generator), the entire grid is turned off and
only the segments are enabled one by one (seg0 to seg7). The segment on time is 64 s.
During the LED discrete time (second cycle), the data present on the internal LED buffer is
checked. If the data is present, then the brightness setting of each LED in the brightness
control register is checked. Then each segment will be enabled or disabled based on the
register value. In this duration, the grids 1 to 6 are turned off. The grid corresponding to LED
digit is turned on. The LED on duty cycle is 14/16. If the LED/seg1 brightness is 12/16, it
means that the segment1 OFF time is 12/16 and on time is 2/16.
During 7-segment display time (3rd cycle to 8th cycle), the display status is checked whether
it is ON or OFF. If display is ON, then the dimming settings are checked from the
configuration register for the grid (it may be common dimming setting or individual dimming
setting for each digit). The minimum turn on time is 1/16 and maximum turn on time is 14/16.
The blanking time is valid before the turning on and turning off of the grid. The blanking
interval is 32 s. This will continue until the maximum number of digits configured in the
register. Once the full cycle is complete, the keyscan cycle will start again.
If the display is not turned on, then the timing generation will immediately go to the key scan
mode.
Initial:
All the segments and grids are turned off.
During operation:
1.
Turn on segment (keyscan) one by one. On time duration is 64 s.
2.
Check the data present in LED register. If data is present, turn on the respective LED
grid and segments.
3.
Check the display on. If display is turned on, then enable the grid one by one from grid
1 to grid 6 (maximum) and turn on segments.
相关PDF资料
PDF描述
STM32F101C8T6 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, PQFP48
STM32F101R6T6 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, PQFP64
STM32F101VBT6 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, PQFP100
STM32F101T6U6 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, QCC36
STM32F101CBT6AXX 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, PQFP48
相关代理商/技术参数
参数描述
STLED325QTR 功能描述:LED照明驱动器 I2C interfaced LED controller/driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
STLED32MAT-EVAL1 功能描述:BOARD EVALUATION FOR LED ARRAY RoHS:否 类别:编程器,开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像,彩色(RGB) 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
STLED524 功能描述:IC MATRIX LED DISPL DVR 56CSP 制造商:stmicroelectronics 系列:- 包装:剪切带(CT) 零件状态:有效 显示类型:LED 配置:点阵 接口:SPI 数字或字符:- 电流 - 电源:- 电压 - 电源:2.7 V ~ 5.5 V 工作温度:-30°C ~ 85°C 安装类型:表面贴装 封装/外壳:56-UFBGA,WLCSP 供应商器件封装:56-CSP(3.4x3.0) 标准包装:1
ST-LEQ1 制造商:Radio Design Labs 功能描述:Use With Vca Loudne Equalizer 制造商:RADIO DESIGN LABS 功能描述:LOUDNESS EQUALIZER USE WITH VCA
STLGCA-1.024 制造商:未知厂家 制造商全称:未知厂家 功能描述:Crystal Oscillator