- 您现在的位置：买卖IC网 > PDF目录18736 > STM1E-SFP02 (Maxim Integrated)MOD TXRX COPPER MSA SFP PDF资料下载
参数资料
| 型号： | STM1E-SFP02 |
| 厂商： | Maxim Integrated |
| 文件页数： | 3/16页 |
| 文件大小： | 0K |
| 描述： | MOD TXRX COPPER MSA SFP |
| 标准包装： | 1 |
| 应用： | 电信 |
| 电源电压： | 3.15 V ~ 3.45 V |
| 电流 - 接收： | 100mA |
| 数据接口： | 串行，USB |
| 工作温度： | -20°C ~ 85°C |
| 封装/外壳： | 模块，连接器 |
| 包装： | 散装 |
STM1E-SFPxx 155Mbps Copper Transceiver
Final Datasheet
Serial ID Interface
The STM1E-SFPxx supports the 2-wire serial EEPROM protocol for the ATMEL AT24C01 as defined by the MSA.
The serial interface provides access to identification information. The memory is organized as byte wide data
words that can be addresses individually or sequentially at device address 1010000X (A0h).
Special Design Considerations for Using STM1E-SFPxx Transceivers
Host enclosures that use SFP devices should provide appropriate clearances between the SFP transceivers to
allow room for the larger width of the 1.0/2.3 mini-coax front end. For most systems a nominal centerline-to-
centerline spacing of 16.25mm (0.640”) is sufficient, but preferred coax cable types and routing clearances may
require additional spacing.
NOTE: To accommodate the preferred Type D coax coupling and cable types, the width of the nosepiece
or front end was designed to exceed the MSA requirements of 13.7mm (+/- 0.1).
o
o
Reference INF-8074 [Appendix A, Table 1, Designator A] for MSA recommendations
Reference Mechanical Drawings section for STM1E-SFPxx transceiver dimensions.
The SFP transceiver insertion slot should be clear of nearby moldings and covers that might block convenient
access to the unique latching mechanism used in the STM1E-SFPxx. A bail-style de-latch was not feasible with a
coaxial network interface so a simple push button actuator was employed. Detaching the coax cable from the
STM1E-SFPxx is not required for de-latching the transceiver from the host card.
NOTES :
1. In order to secure the larger push button de-latch mechanism, the length of the bottom of the
transceiver exceeds the maximum MSA requirements of 2.0mm.
o
o
Reference INF-8074 [Appendix A, Table 1, Designator Y] for MSA recommendations
Reference Mechanical Drawings section for STM1E-SFPxx transceiver dimensions.
2. Note: Double-sided board mounting is generally not recommended due to the limited clearance
for de-latching the STM1E-SFPxx transceiver.
STM1E-SFPxx Datasheet
-3-
August 2008 v2-2
相关PDF资料 |
PDF描述 |
|---|---|
| 7C-40.000MBB-T | OSC 40.000 MHZ 3.3V SMD |
| OH300-61003CV-010.0M | OSC OCVCXO 10.000 MHZ 3.3V |
| FI212L062007-T | FILTER LOWPASS DTV DVB-H SMD |
| OH100-61003CV-010.0M | OSC OCVCXO 10.000 MHZ 3.3V |
| PIXLITE-SO-PLFE | MODULE ZIGBEE SW FAST 24-SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| STM1E-SFP02 #DUPLICATE# | 制造商:Maxim Integrated Products 功能描述: |
| STM1E-SFP-03 | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| STM1E-SFP08 | 功能描述:LIN 收发器 155Mbps Copper Transceiver RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
| STM1E-SFP16 | 功能描述:LIN 收发器 RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
| STM1E-SFP22 | 功能描述:LIN 收发器 RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
发布紧急采购，3分钟左右您将得到回复。