- 您现在的位置：买卖IC网 > PDF目录18712 > SX1223SK915 (Semtech)KIT STARTER FOR XE1223 915MHZ PDF资料下载
参数资料
| 型号： | SX1223SK915 |
| 厂商： | Semtech |
| 文件页数： | 8/25页 |
| 文件大小： | 0K |
| 描述： | KIT STARTER FOR XE1223 915MHZ |
| 产品培训模块： | SX1223 ISM Transmitter |
| 标准包装： | 1 |
| 类型： | 发射器，UHF |
| 频率： | 915MHz |
| 适用于相关产品： | XE1223（915MHz） |
| 已供物品： | 2 个板，2 个模块，2 根天线，线缆，文档 |
| 产品目录页面： | 584 (CN2011-ZH PDF) |
SX1223
frequencies corresponding to the transmission of the two possible values ‘0’ and ‘1’; these frequencies are then
separated by twice the specified single sided frequency deviation ? f.
4.1.2 Crystal Oscillator
The crystal oscillator (XCO) provides the PLL with the reference signal. The schematic of the crystal oscillator's
external components for 16 MHz is shown in Figure 2.
XTB, pin 7
5p6
5p6
XTA, pin 8
Figure 2 : External crystal oscillator circuit with additional (optional) external capacitances
The crystal should be connected between pins XTA and XTB (pin 8 and 7). Either internal or external loading
capacitors for the crystal can be used. Internal capacitors can be enabled by setting the XCOcap_en bit to 1. Faster
start-up time is expected when using external capacitors. The total capacitance when XCOcap_en=1 (and no
external capacitors) is 9 pF. Using a crystal with a load capacitance of 9 pF will give the expected oscillation
frequency.
If XCOcap_en=0, the loading capacitors can be calculated by the following formula:
C L =
1
C 1
1
+
1
C 2
+ C parasitic
The parasitic capacitance is the pin input capacitance and PCB stray capacitance. For instance, for a 9pF load
crystal and a total parasitic capacitance of 6 pF the recommended values of the external load capacitors are 5.6 pF.
If an external reference is going to be used instead of a crystal, the signal shall be applied to pin 7, XTB. Due to
internal biasing, AC coupling is recommended for use between the external reference and the XTB pin.
The start-up time of the crystal oscillator can vary from 150us to 800us depending on the settings shown in Table
15. Therefore, to save current consumption, the XCO should be turned on before any other circuit block. During
start-up the XCO amplitude will eventually reach a sufficient level to trigger the M-counter. After counting 2 M-
counter output pulses the rest of the circuit is enabled.
Two bits are available to speed up the crystal oscillator start-up: XCO_high_I increases the bias current and
XCO_quick_start boosts this current but only at the start; the first output pulse from the M-divider turns this boost
current off. Typical values for XCO start-up time and current consumption are tablulated below:
XCO_quick_start, XCO_high_I
IDDST [uA]
TS_OS [us]
00
200
800
01
250
750
10
900
200
11
950
150
Table 1 : Oscillator start-up time
A reference clock can be generated by SX1223 for use by an external microcontroller. The ClkOut_en configuration
bit determines the status of the CLKOUT pin. When set high CLKOUT is enabled, otherwise it’s disabled. When
enabled, the output frequency at CLKOUT is the crystal oscillator frequency divided by 16, and is then 1 MHz for a
crystal at 16 MHz. This clock signal is disabled in Sleep Mode. When disabled, the CLKOUT pin is set to ground.
4.1.3 VCO
The VCO is fully integrated and has no external components. It oscillates at 1.8 GHz and is divided by 2 or 4 in the
900 MHz or the 450 MHz band respectively (FreqBand = 1 or 0). Additionally two bits in the configuration registers
set the VCO frequency and three bits control the bias current. The two VCO_freq bits have to be programmed by
? Semtech 2007
8
www.semtech.com
相关PDF资料 |
PDF描述 |
|---|---|
| TC50V6A32K7680 | OSCILLATOR 32.7680 KHZ 1.5V SMD |
| TC70V3A32K7680 | OSCILLATOR 32.7680 KHZ 1.5V SMD |
| 3341-07 | PROGRAMMING BOARD FOR PE3341 |
| 3342-07 | PROGRAMMING BOARD FOR PE3342 |
| TC70V3C32K7680 | OSCILLATOR 32.7680 KHZ 1.5V SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SX1230 | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Integrated Transmitter IC Narrow/wideband 315 MHz, 434 MHz 868 MHz and 915 MHz band Transmitter |
| SX1230-11SKA433 | 制造商:Semtech Corporation 功能描述:Evaluation Kit For SX1230-11SKA 433 mHz (SX1230SKA /SX1211SKA board) Transmitter |
| SX1230-11SKA868 | 制造商:Semtech Corporation 功能描述:NARROW/WIDEBAND RF TRANSMITTER 868MHZ |
| SX1230-11SKA915 | 制造商:Semtech Corporation 功能描述:NARROW/WIDEBAND RF TRANSMITTER 915MHZ 制造商:Semtech Corporation 功能描述:Evaluation Kit For SX1230-11SKA 915 mHz (SX1230SKA /SX1211SKA board) |
| SX1230-12SKA433 | 制造商:Semtech Corporation 功能描述:USB KIT - SX1230 433MHZ 制造商:Semtech Corporation 功能描述:Deluxe USB Starter Kit for SX1230, Includes Two USB Interface Boards at 433MHz |
发布紧急采购，3分钟左右您将得到回复。