Micrel, Inc.
SY88149HL
June 2010
4
M9999-061110-I
Absolute Maximum Ratings
(1)
Supply Voltage (VCC) ....................................... 0V to +4.0V
Input Voltage (DIN, /DIN) .......................................0 to VCC
Output Current (IOUT)
Continuous........................................................ ±50mA
Surge .............................................................. ±100mA
TTL Inputs Voltage .................................................0 to VCC
VREF Current .......................................... -
800μA to +500μA
LOS/SDLVL Voltage............................................VREF to VCC
Lead Temperature (soldering, 20sec.) ..................... 260°C
Storage Temperature (Ts) ....................... –65°C to +150°C
Operating Ratings
(2)
Supply Voltage (VCC)................................. +3.0V to +3.6V
Ambient Temperature (TA).......................–40°C to +85°C
Junction Temperature (TJ) .....................–40°C to +125°C
Junction Thermal Resistance
(3)
QFN (
θ
JA) Still-air .............................................60°C/W
QFN (
Ψ
JB) Junction-to-board ...........................38°C/W
DC Electrical Characteristics
VCC = 3.0 to 3.6V; TA = –40°C to +85°C, typical values at VCC = 3.3V, TA = 25°C.
Symbol
Parameter
Condition
Min
Typ
Max
Units
ICC
Power Supply Current
No output load
57
78
mA
LOS/SDLVL
LOS/SDLVL Voltage
VREF
VCC
V
VOH
LVPECL Output HIGH Voltage
50
to VCC-2V
VCC-1.085
VCC-0.955
VCC-0.880
V
VOL
LVPECL Output LOW Voltage
50
to VCC-2V
VCC-1.830
VCC-1.705
VCC-1.555
V
IOFFSET
Input Offset Voltage
1
mV
VIHCMR
Common Mode Range
GND+2.0
VCC
V
VREF
Reference Voltage
VCC-1.48
VCC-1.32
VCC-1.16
V
LVTTL DC Electrical Characteristics
VCC = 3.0 to 3.6V; TA = –40°C to +85°C, typical values at VCC = 3.3V, TA = 25°C.
Symbol
Parameter
Condition
Min
Typ
Max
Units
VIH
TTL Input HIGH Voltage
2.0
V
VIL
TTL Input LOW Voltage
0.8
V
IIH
TTL Input HIGH Current
(/AUTORESET, JAM, LOS/SDSEL)
VIN = 2.7V
VIN = VCC
20
100
A
IIL
TTL Input LOW Current
(/AUTORESET, JAM, LOS/SDSEL)
VIN = 0.5V
-0.3
mA
IIH
TTL Input HIGH Current (RESET)
VIN = 2.7V
VIN = VCC
200
300
A
IIL
TTL Input LOW Current (RESET)
VIN = 0.5V
-0.05
mA
VOL
TTL Output LOW Level
IOL = +20mA
0.5
V
Notes:
1. Permanent device damage may occur if absolute maximum ratings are exceeded. This is a stress rating only and functional operation is not implied
at conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum rating conditions
for extended periods may affect device reliability.
2. The data sheet limits are not guaranteed if the device is operated beyond the operating ratings.
3. Thermal performance assumes the use of a 4-layer PCB. Exposed pad must be soldered (or equivalent) to the device’s most negative potential on
the PCB
.