参数资料
| 型号： | T89C51AC2-RLTIM |
| 厂商： | Atmel |
| 文件页数： | 79/121页 |
| 文件大小： | 0K |
| 描述： | IC 8051 MCU FLASH 32K 44VQFP |
| 标准包装： | 160 |
| 系列： | 89C |
| 核心处理器： | 8051 |
| 芯体尺寸： | 8-位 |
| 速度： | 40MHz |
| 连通性： | UART/USART |
| 外围设备： | POR，PWM，WDT |
| 输入/输出数： | 34 |
| 程序存储器容量： | 32KB（32K x 8） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 2K x 8 |
| RAM 容量： | 1.25K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 3 V ~ 5.5 V |
| 数据转换器： | A/D 8x10b |
| 振荡器型： | 外部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 44-LQFP |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页当前第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页
60
A/T89C51AC2
4127H–8051–02/08
Timer 1
Timer 1 is identical to Timer 0 excepted for Mode 3 which is a hold-count mode. The fol-
lowing comments help to understand the differences:
Timer 1 functions as either a Timer or event Counter in three modes of operation.
1’s mode 3 is a hold-count mode.
Timer 1 is controlled by the four high-order bits of TMOD register (see Figure 40)
and bits 2, 3, 6 and 7 of TCON register (see Figure 39). TMOD register selects the
method of Timer gating (GATE1), Timer or Counter operation (C/T1#) and mode of
operation (M11 and M01). TCON register provides Timer 1 control functions:
overflow flag (TF1), run control bit (TR1), interrupt flag (IE1) and interrupt type
control bit (IT1).
Timer 1 can serve as the Baud Rate Generator for the Serial Port. Mode 2 is best
suited for this purpose.
For normal Timer operation (GATE1 = 0), setting TR1 allows TL1 to be incremented
by the selected input. Setting GATE1 and TR1 allows external pin INT1# to control
Timer operation.
Timer 1 overflow (count rolls over from all 1s to all 0s) sets the TF1 flag generating
an interrupt request.
When Timer 0 is in mode 3, it uses Timer 1’s overflow flag (TF1) and run control bit
(TR1). For this situation, use Timer 1 only for applications that do not require an
interrupt (such as a Baud Rate Generator for the Serial Port) and switch Timer 1 in
and out of mode 3 to turn it off and on.
It is important to stop Timer/Counter before changing mode.
Mode 0 (13-bit Timer)
Mode 0 configures Timer 1 as a 13-bit Timer, which is set up as an 8-bit Timer (TH1 reg-
ister) with a modulo-32 prescaler implemented with the lower 5 bits of the TL1 register
(see Figure 31). The upper 3 bits of TL1 register are ignored. Prescaler overflow incre-
ments TH1 register.
Mode 1 (16-bit Timer)
Mode 1 configures Timer 1 as a 16-bit Timer with TH1 and TL1 registers connected in
cascade (see Figure 32). The selected input increments TL1 register.
Mode 2 (8-bit Timer with Auto-
Reload)
Mode 2 configures Timer 1 as an 8-bit Timer (TL1 register) with automatic reload from
TH1 register on overflow (see Figure 33). TL1 overflow sets TF1 flag in TCON register
and reloads TL1 with the contents of TH1, which is preset by software. The reload
leaves TH1 unchanged.
Mode 3 (Halt)
Placing Timer 1 in mode 3 causes it to halt and hold its count. This can be used to halt
Timer 1 when TR1 run control bit is not available i.e. when Timer 0 is in mode 3.
Interrupt
Each Timer handles one interrupt source that is the timer overflow flag TF0 or TF1. This
flag is set every time an overflow occurs. Flags are cleared when vectoring to the Timer
interrupt routine. Interrupts are enabled by setting ETx bit in IEN0 register. This assumes
interrupts are globally enabled by setting EA bit in IEN0 register.
相关PDF资料 |
PDF描述 |
|---|---|
| DSPIC33FJ16GS402-I/MM | IC DSPIC MCU/DSP 16K 28-QFN |
| T89C5115-TISIM | IC 8051 MCU FLASH 16K 28SOIC |
| PIC18F27J13-I/SP | IC PIC MCU 128KB FLASH 28SPDIP |
| T89C5115-TDSIM | IC 8051 MCU FLASH 16K 24SOIC |
| 52893-2090 | CONN FFC 20POS .50MM R/A ZIF SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| T89C51AC2-RLTI-M | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit MCU with 32K bytes Flash, 10 bits A/D and EEPROM |
| T89C51AC2-SLSC-M | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit MCU with 32K bytes Flash, 10 bits A/D and EEPROM |
| T89C51AC2-SLSE-M | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit MCU with 32K bytes Flash, 10 bits A/D and EEPROM |
| T89C51AC2-SLSIM | 功能描述:IC 8051 MCU FLASH 32K 44PLCC RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:89C 标准包装:9 系列:87C 核心处理器:8051 芯体尺寸:8-位 速度:40/20MHz 连通性:UART/USART 外围设备:POR，WDT 输入/输出数:32 程序存储器容量:32KB（32K x 8） 程序存储器类型:OTP EEPROM 大小:- RAM 容量:256 x 8 电压 - 电源 (Vcc/Vdd):4.5 V ~ 5.5 V 数据转换器:- 振荡器型:内部 工作温度:0°C ~ 70°C 封装/外壳:40-DIP（0.600"，15.24mm） 包装:管件 |
| T89C51AC2-SLSI-M | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit MCU with 32K bytes Flash, 10 bits A/D and EEPROM |
发布紧急采购，3分钟左右您将得到回复。