参数资料
型号: TA1204AF
元件分类: 消费家电
英文描述: SPECIALTY CONSUMER CIRCUIT, PQFP44
封装: 14 X 14 MM, 0.80 MM PITCH, PLASTIC, QFP-44
文件页数: 8/25页
文件大小: 575K
代理商: TA1204AF
TA1204AF
2001-02-07 16/25
Note 16:
Signal frequency characteristics, inter-axis deviation
Test condition 5 (CP mode, fixed polarity)
Input :
X In1
Test signal 2 (sweep)
Input test signal 2 to X In1, raise its frequency from 500kHz to 20MHz, and observe the amplitudes
of the frequency components. Measure the frequency for a 3dB fall in output amplitude. Take the
same measurements as for positive polarity by changing SW7B from a to b.
Note 17:
Output dynamic range
Test condition 4 (CP mode)
Input :
X In1
Test signal 3
VR23 : →Max / Min
Input a signal (0.7Vp-p) including black and white levels to input A (X In1). Change SW23 from a to b,
raise and lower the voltage applied to pin 23 by turning VR23 clockwise and anticlockwise, measure
the maximum and minimum black waveform levels for an output pin (pin 21 when X = B, pin 19
when X = G, and pin 14 when X = R), and thus obtain the voltage difference.
Note 18:
Signal output through-rate
Test condition 4 (CP mode)
Input :
X In1
Test signal 5
Input to input A (X In1) a test signal whose 10 to 90% rise / fall times are less than 50ns in a
rectangular waveform that repeats black and white levels. Measure the 10 to 90% rise / fall times in
the waveform of the output pin (pin 21 when X = B, pin 19 when X = G, and pin 14 when X = R), and
convert this to a through-rate.
Note 19:
Signal output S / N
Test condition 5 (CP mode, fixed polarity)
Input : no signal
Noise measurement band DC to 6MHz
Change SW27 from a to b, and adjust VR27 while looking at the waveform of an output pin (pin 21,
pin 19, pin 14) so that the difference between the γ0 and black levels becomes 0. Measure the noise
voltage (measurement band: ~6MHz) of the output pins in this state. Repeat this measurement for
each output pin. Calculate the ratio of the No. 9 typical output amplitude to the measured noise
voltage, and express it in dB units.
For a positive polarity measurement, repeat the above measurement by changing SW7B from a to b.
Note 20:
Reversed polarity center voltage, typical value, inter-axis deviation
Test condition 4 (CP mode)
Input : no signal
Measure the γ0 levels of the positive and negative polarities of the output waveform at an output pin
(pin 21 when X = B, pin 19 when X = G, and pin 14 when X = R), and measure the mean value of the
two levels.
Repeat this measurement replacing B, G, and R as the X-axis.
Note 21:
Reversed polarity center voltage, maximum and minimum variable ranges, inter-axis deviation
Test condition 4 (CP mode)
Input : no signal
VR23 : →Max / →Min
Change SW25 from a to b, adjust VR26 and set the voltage applied to pin 25 at 5V, thereby
minimizing the cut-off. Change SW23 from a to b, raise and lower the voltage applied to pin 23 by
turning VR23 clockwise and anticlockwise. Obtain the center voltage of the positive and negative γ0
levels when the waveform of an output pin (pin 21 when X = B, pin 19 when X = G and pin 14 when
X = R) approaches VDD and stops rising, and set this as the maximum value. Obtain the center
voltage of positive and negative γ0 levels when the waveform of the output pin approaches GND and
these levels stop decreasing, and make this voltage the minimum value.
Repeat this measurement replacing B, G, and R as the X-axis.
相关PDF资料
PDF描述
TA1209F AM/FM, AUDIO/VIDEO DEMODULATOR, PQFP48
TA1211N COLOR SIGNAL DECODER, PDIP54
TA1216AN 3 CHANNEL(S), TONE CONTROL CIRCUIT, PDIP30
TA1217AF 4 CHANNEL(S), TONE CONTROL CIRCUIT, PDSO36
TA1217AN 4 CHANNEL(S), TONE CONTROL CIRCUIT, PDIP36
相关代理商/技术参数
参数描述
TA1205 制造商:Crydom 功能描述:
TA1207 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:FOR LCD TVS, PIF AND SIF SYSTEM
TA1207F 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:FOR LCD TVS, PIF AND SIF SYSTEM
TA1209F 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:FOR LCD TVS, SEPARATE CARRIER PIF AND SIF SYSTEMS
TA120BLKGRN 制造商:E-Switch Inc 功能描述: