参数资料
型号: TAS5028APAG
厂商: TEXAS INSTRUMENTS INC
元件分类: 消费家电
英文描述: SPECIALTY CONSUMER CIRCUIT, PQFP64
封装: GREEN, PLASTIC, TQFP-64
文件页数: 29/82页
文件大小: 1347K
代理商: TAS5028APAG
TAS5028A Controls and Status
28
SLES112 — June 2004
TAS5028A
Table 24. Device Outputs During Backend Error
SIGNAL
SIGNAL STATE
Valid
Low
PWM P-outputs
M-State low
PWM M-outputs
M-State low
HPPWM P-outputs
M-State low
HPPWM M-outputs
M-State low
SDA
Signal Input (not driven)
2.2.4 Speaker / Headphone Selector (HP_SEL)
The HP_SEL terminal enables the headphone output or the speaker outputs. The headphone output receives
the processed data output from DAP and PWM channels 1 and 2.
In 6-channel configuration this feature does not affect the two lineout channels.
When low, the headphone output is enabled. In this mode the speaker outputs are disabled. When high, the
speaker outputs are enabled and the headphone is disabled.
Changes in the pin logic level results in a state change sequence using soft mute to the hard mute (M) state
for both speaker and headphone followed by a soft unmute.
When HP_SEL is low, the configuration of channels 1 and 2 are defined by the headphone configuration
register. When HP_SEL is high, the channel 1 and 2 configuration registers define the configuration of
channels 1 and 2.
2.2.5 Mute (MUTE)
The mute control provides a noiseless volume ramp to silence. Releasing mute provides a noiseless ramp
to previous volume. The TAS55508 has both a master and individual channel mute commands. A terminal
is also provided for the master MUTE. The low active master Mute I2C register and the MUTE terminal are
logically Or’ed together. If either is set to low, a mute on all channels is performed. The master mute command
operates on all channels regardless on whether the system is in six or eight channel configuration.
When MUTE is invoked, the PWM output stops switching and then goes to an idle state.
The master Mute terminal is used to support a variety of other operations in the TAS5028A, such as setting
the inter-channel delay, the serial interface format, and the clock rates. A mute command by the master mute
terminal, individual I2C mute, the AM interference mute sequence, the bank switch mute sequence, or
automute overrides an unmute command or a volume command. While a mute is active, the commanded
channels will be placed in a mute state. When a channel is unmuted, it goes to the last commanded volume
setting that has been received for that channel.
2.3
Device Configuration Controls
The TAS5028A provides a number of system configuration controls that are set at initialization and following
a reset.
Channel configuration
Headphone configuration
Audio system configurations
Recovery from clock error
Volume and mute update rate
Modulation index limit
Inter-channel delay
Master clock and data rate controls
Bank controls
相关PDF资料
PDF描述
TAS5028PAG SPECIALTY CONSUMER CIRCUIT, PQFP64
TAS5028PAGR SPECIALTY CONSUMER CIRCUIT, PQFP64
TAS5028PAGG4 SPECIALTY CONSUMER CIRCUIT, PQFP64
TAS5028PAGRG4 SPECIALTY CONSUMER CIRCUIT, PQFP64
TAS5036AIPFC SPECIALTY CONSUMER CIRCUIT, PQFP80
相关代理商/技术参数
参数描述
TAS5028APAGG4 功能描述:音频放大器 8Ch Dig Aud PWM Proc RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel
TAS5028APAGR 功能描述:音频放大器 8Ch Dig Aud PWM Proc RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel
TAS5028APAGRG4 功能描述:音频放大器 8Ch Dig Aud PWM Proc RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel
TAS5028PAG 功能描述:音频 DSP 8 Ch Digital Audio PWM Processor RoHS:否 制造商:Texas Instruments 工作电源电压: 电源电流: 工作温度范围: 安装风格: 封装 / 箱体: 封装:Tube
TAS5028PAGG4 功能描述:音频 DSP 8 Ch Digital Audio PWM Processor RoHS:否 制造商:Texas Instruments 工作电源电压: 电源电流: 工作温度范围: 安装风格: 封装 / 箱体: 封装:Tube