参数资料
型号: TAS5414ATPHDMQ1
厂商: TEXAS INSTRUMENTS INC
元件分类: 音频/视频放大
英文描述: 116 W, 4 CHANNEL, AUDIO AMPLIFIER, PQFP64
封装: GREEN, PLASTIC, HTQFP-64
文件页数: 9/54页
文件大小: 1386K
代理商: TAS5414ATPHDMQ1
OUT1_M
OUT1_P
V
(OUT1_P – OUT1_M)
Speaker
Playback
/
Mute
Hi-Z
ChannelSynchronization
Phase1
Phase2
Phase3
Phase4
S2G
200ms
<200ms
S2P
200ms
OL
150ms
SL
150ms
~50ms
T0188-01
SLOS535C
– MAY 2009 – REVISED APRIL 2011
Power FETs
The BTL output for each channel comprises four rugged N-channel 30-V FETs, each of which has an RDSon of 75
m
for high efficiency and maximum power transfer to the load. These FETs are designed to handle large
voltage transients during load dump.
Load Diagnostics
The TAS5414A and TAS5424A incorporate load diagnostic circuitry designed to help pinpoint the nature of
output misconnections during installation. The TAS5414A and the TAS5424A include functions for detecting and
determining the status of output connections. The following diagnostics are supported:
Short to GND
Short to PVDD
Short across load (R
< 1 , typical)
Open load (R
> 800 , typical)
Tweeter detection
The presence of any of the short or open conditions is reported to the system via I2C register read. The tweeter
detect status can be read from the CLIP_OTW pin when properly configured.
1. Output Short and Open Diagnostics
—The TAS5414A and TAS5424A contain circuitry designed to detect
shorts and open conditions on the outputs. The load diagnostic function can only be invoked when the output
is in the Hi-Z mode. There are four phases of test during load diagnostics and two levels of test. In the full
level, all channels must be in the Hi-Z state. All four phases are tested on each channel, all four channels at
the same time. When fewer than four channels are in Hi-Z, the reduced level of test is the only available
option. In the reduced level, only short to PVDD and short to GND can be tested. Load diagnostics can occur
at power up before the amplifier is moved out of Hi-Z mode. If the amplifier is already in play mode, it must
Mute and then Hi-Z before the load diagnostic can be performed. By performing the mute function, the
normal pop- and click-free transitions occur before the diagnostics begin. The diagnostics are performed as
shown in Figure 13. Figure 14 shows the impedance ranges for the open-load and shorted-load diagnostics.
The results of the diagnostic are read from the diagnostic register for each channel via I2C. Note: Do not
send a command via I2C to register 0x0C during the load diagnostic test.
Figure 13. Load Diagnostics Sequence of Events
Copyright
2009–2011, Texas Instruments Incorporated
17
相关PDF资料
PDF描述
TAS5414ATPHDQ1 116 W, 4 CHANNEL, AUDIO AMPLIFIER, PQFP64
TAS5414ATPHDRMQ1 116 W, 4 CHANNEL, AUDIO AMPLIFIER, PQFP64
TAS5414ATPHDRQ1 116 W, 4 CHANNEL, AUDIO AMPLIFIER, PQFP64
TAS5414ATDKDMQ1G4 116 W, 4 CHANNEL, AUDIO AMPLIFIER, PDSO36
TAS5414ATDKDRMQ1G4 116 W, 4 CHANNEL, AUDIO AMPLIFIER, PDSO36
相关代理商/技术参数
参数描述
TAS5414ATPHDMQ1G4 功能描述:音频放大器 4 Channel Auto Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel
TAS5414ATPHDQ1 功能描述:音频放大器 4Ch Auto Dig Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel
TAS5414ATPHDQ1G4 功能描述:音频放大器 4 Channel Auto Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel
TAS5414ATPHDRMQ1 功能描述:音频放大器 4Ch Auto Dig Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel
TAS5414ATPHDRMQ1G4 功能描述:音频放大器 4 Channel Auto Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel