- 您现在的位置：买卖IC网 > PDF目录383879 > TB28F800BV-B80 (INTEL CORP) 2-MBIT SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY PDF资料下载
参数资料
| 型号： | TB28F800BV-B80 |
| 厂商： | INTEL CORP |
| 元件分类： | DRAM |
| 英文描述： | 2-MBIT SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| 中文描述： | 1M X 8 FLASH 5V PROM, 80 ns, PDSO44 |
| 封装： | 0.525 X 1.110 INCH, PLASTIC, SOP-44 |
| 文件页数： | 29/55页 |
| 文件大小： | 638K |
| 代理商： | TB28F800BV-B80 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页
E
4.2.1
2-MBIT SmartVoltage BOOT BLOCK FAMILY
29
SEE NEW DESIGN RECOMMENDATIONS
APPLYING VCC VOLTAGES
When applying V
CC
voltage to the device, a delay
may be required before initiating device operation,
depending on the V
CC
ramp rate. If V
CC
ramps
slower than 1V/100 μs (0.01 V/μs) then no delay is
required. If V
CC
ramps faster than 1V/100 μs (0.01
V/μs), then a delay of 2 μs is required before
initiating device operation. RP# = GND is
recommended during power-up to protect against
spurious write signals when V
CC
is between V
LKO
and V
CCMIN
.
V
CC
Ramp Rate
Required Timing
≤
1V/100
μ
s
No delay required.
> 1V/100
μ
s
A delay time of 2
μ
s is required before any device operation is initiated, including read
operations, command writes, program operations, and erase operations. This delay
is
measured beginning from the time V
CC
reaches V
CCMIN
(3.0 V for 3.3
±
0.3 V operation;
and 4.5 V for 5 V operation).
NOTES:
1.
2.
These requirements must be strictly followed to guarantee all other read and write specifications.
To switch between 3.3 V and 5 V operation, the system should first transition V
from the existing voltage range to GND,
and then to the new voltage. Any time the V
CC
supply drops below V
CCMIN
, the chip may be reset, aborting any operations
pending or in progress.
These guidelines must be followed for any V
CC
transition from GND.
3.
4.3
T
A
= 25 °C, f = 1 MHz
Capacitance
Symbol
Parameter
Note
Typ
Max
Unit
Conditions
C
IN
Input Capacitance
1
6
8
pF
V
IN
= 0 V
C
OUT
Output Capacitance
1, 2
10
12
pF
V
OUT
= 0 V
NOTES:
1. Sampled, not 100% tested.
2. For the 28F002B, address pin A
10
follows the C
OUT
capacitance numbers.
相关PDF资料 |
PDF描述 |
|---|---|
| TB28F800BV-T80 | 2-MBIT SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| TB28F800BVB90 | 8-MBIT (512K X 16, 1024K X 8) SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| TB28F800BVT90 | 8-MBIT (512K X 16, 1024K X 8) SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| TB28F800CV-B80 | 2-MBIT SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| TB28F800CV-T60 | 2-MBIT SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TB28F800BVB90 | 制造商:INTEL 制造商全称:Intel Corporation 功能描述:8-MBIT (512K X 16, 1024K X 8) SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| TB28F800BV-T60 | 制造商:INTEL 制造商全称:Intel Corporation 功能描述:2-MBIT SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| TB28F800BV-T80 | 制造商:INTEL 制造商全称:Intel Corporation 功能描述:2-MBIT SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| TB28F800BVT90 | 制造商:INTEL 制造商全称:Intel Corporation 功能描述:8-MBIT (512K X 16, 1024K X 8) SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| TB28F800CV-B60 | 制造商:INTEL 制造商全称:Intel Corporation 功能描述:2-MBIT SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
发布紧急采购，3分钟左右您将得到回复。