- 您现在的位置：买卖IC网 > PDF目录98166 > TB62201AF STEPPER MOTOR CONTROLLER, 1.5 A, PDSO38 PDF资料下载
参数资料
| 型号： | TB62201AF |
| 元件分类： | 运动控制电子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 1.5 A, PDSO38 |
| 封装： | 0.450 INCH, 0.65 MM PITCH, HEAT SINK, PLASTIC, SOP-36/38 |
| 文件页数： | 5/89页 |
| 文件大小： | 1396K |
| 代理商： | TB62201AF |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页
TB62201AF
2005-04-04
13
7. SETUP Functions
Input
Function
H
Decay timing data input mode
L
Normal operating mode
Note: The SETUP pin is pulled down in the IC by 10-k
resistor.
8. Serial Data Input Setting (Normal operation)
SETUP pin: L
Note: Data input to the DATA pin are 16-bit serial data.
Data are transferred from DATA 0 (Torque 0) to DATA 15 (Phase A). Data are input and transferred at the
following timings.
At CLK falling edge: data input
At CLK rising edge: data transfer
After data are transferred, all data are latched on the rising edge of the STROBE signal.
As long as STROBE is not rising, the signal can be either Low or High during data transfer.
9. Serial Data Input Setting (Decay timing setup)
SETUP pin: H
Note: Data input to the DATA pin are 16-bit serial data.
Data are transferred from DATA 0 (Current Mode 1) to DATA 15 (DECAY MODE X-4). Data are input and
transferred at the following timings.
At CLK falling edge: data input
At CLK rising edge: data transfer
After data are transferred, all data are latched on the rising edge of the STROBE signal.
As long as STROBE is not rising, the signal can be either Low or High during data transfer.
DATA
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
CLK
STROBE
DATA
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
CLK
STROBE
相关PDF资料 |
PDF描述 |
|---|---|
| TB62206F | STEPPER MOTOR CONTROLLER, 1.8 A, PDSO22 |
| TB62209FG | STEPPER MOTOR CONTROLLER, 1.8 A, PDSO38 |
| TB62214FTG | STEPPER MOTOR CONTROLLER, 2 A, PQCC48 |
| TB62754AFNG | SWITCHING REGULATOR, PDSO20 |
| TB62756FUG | SWITCHING REGULATOR, 1430 kHz SWITCHING FREQ-MAX, PDSO6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TB62201AFG | 制造商:Toshiba 功能描述:Stepper Motor Driver 5V 38-Pin (36+2Tab) HSOP 制造商:Toshiba 功能描述:Stepper Motor Driver 5V 38-Pin (36+2Tab) HSOP Cut Tape |
| TB62201AFG(EL) | 功能描述:马达/运动/点火控制器和驱动器 Combination Motor Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TB62202AFG | 制造商:Toshiba America Electronic Components 功能描述: |
| TB62202AFG(EL) | 功能描述:马达/运动/点火控制器和驱动器 Combination Motor Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TB62206FG | 制造商:Toshiba America Electronic Components 功能描述:2-Phase Stepping Motor Driver 5V 22-Pin(20+2Tab) HSOP |
发布紧急采购，3分钟左右您将得到回复。