收藏本站
参数资料
型号： TB62209FG
元件分类： 运动控制电子
英文描述： STEPPER MOTOR CONTROLLER, 1.8 A, PDSO38
封装： 0.450 INCH, 0.65 MM PITCH, PLASTIC, HSOP-26/38
文件页数： 11/51页
文件大小： 501K
代理商： TB62209FG
TB62209FG
2005-03-02
19
Electrical Characteristics 3 (unless otherwise specified, Ta
= 25°C, VDD = 5 V, VM = 24 V)
Characteristics
Symbol
Test
Circuit
Test Condition
Min
Typ.
Max
Unit
Vref input voltage
Vref
DC
VM = 24 V, VDD = 5 V,
STANDBY
= H, RESET = L,
Output on, CLK
= 1 kHz
2.0
VDD
V
Vref input current
Iref
DC
STANDBY
= H, RESET = L,
Output off, VM = 24 V,
VDD = 5 V, Vref = 3.0 V
20
35
50
A
Vref attenuation ratio
Vref (GAIN)
DC
VM = 24 V, VDD = 5 V,
STANDBY
= H, RESET= L,
Output on,
Vref = 2.0 to VDD 1.0 V
1/4.8
1/5.0
1/5.2
TSD temperature
(Note 1)
TjTSD
DC
VDD = 5 V, VM = 24 V
130
170
°C
TSD return temperature difference
(Note 1)
TjTSD
DC
TjTSD = 130 to 170°C
TjTSD
50
TjTSD
35
TjTSD
20
°C
VDD return voltage
VDDR
DC
VM = 24 V, STANDBY = H
2.0
3.0
4.0
V
VM return voltage
VMR
DC
VDD = 5 V, STANDBY = H
2.0
3.5
5.0
V
Over current protected circuit
operation current
(Note 2)
ISD
DC
VDD = 5 V, VM = 24 V
3.0
A
High temperature monitor pin
output current
Iprotect
DC
VDD = 5 V,
TSD
= operating condition
1.0
3.0
5.0
mA
Electrical angle monitor pin output
current
IMO
DC
VDD = 5 V,
electrical angle
= 0°
(IB
= 100%, IA = 0%)
1.0
3.0
5.0
mA
Vprotect (H)
DC
VDD = 5 V,
TSD
= operating condition
5.0
High temperature monitor pin
output voltage
Vprotect (L)
DC
VDD = 5 V,
TSD
= not operating
condition
0.0
V
VMO2 (H)
DC
VDD = 5 V,
electrical angle
= except 0°
(IB
= 100%,
IA
= Except 0% set)
5.0
Electrical angle monitor pin output
voltage
VMO2 (L)
DC
VDD = 5 V,
electrical angle
= 0°
(IB
= 100%, IA = 0%)
0.0
V
Note 1: Thermal shut down (TSD) circuit
When the IC junction temperature reaches the specified value and the TSD circuit is activated, the internal
reset circuit is activated switching the outputs of both motors to off.
When the temperature is set between 130 (min) to 170°C (max), the TSD circuit operates.
When the TSD circuit is activated, the charge pump is halted, and TROTECT pin outputs VDD voltage.
Even if the TSD circuit is activated and
Standby goes H → L → H instantaneously, the IC is not reset until
the IC junction temperature drops 20°C (typ.) below the TSD operating temperature (hysteresis function).
Note 2: Overcurrent protection circuit
When current exceeding the specified value flows to the output, the internal reset circuit is activated, and the
ISD turns off the output.
Until the Standby signal goes Low to High, the overcurrent protection circuit remains activated.
During ISD, IC turns Standby mode and the charge pump halts.
相关PDF资料
PDF描述
TB62214FTG STEPPER MOTOR CONTROLLER, 2 A, PQCC48
TB62754AFNG SWITCHING REGULATOR, PDSO20
TB62756FUG SWITCHING REGULATOR, 1430 kHz SWITCHING FREQ-MAX, PDSO6
TB62757FUG SWITCHING REGULATOR, 1430 kHz SWITCHING FREQ-MAX, PDSO6
TB6512AFG STEPPER MOTOR CONTROLLER, 0.12 A, PDSO24
相关代理商/技术参数
参数描述
TB62209FG(EL) 功能描述:马达/运动/点火控制器和驱动器 Stepping Motor Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
TB62209FG(O,EL) 功能描述:马达/运动/点火控制器和驱动器 Stepping Motor PWM 40V 1.8A RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
TB62209SN 制造商:THOMAS & BETTS 功能描述:
TB622-100.0M 制造商:Connor-Winfield 功能描述:OSC TCXO 100MHZ 3.3V SMD
TB-6221-01 功能描述:界面模块 SWITCH TERMINATION BRD 62P D-SUB FEMALE RoHS:否 制造商:4D Systems 产品:Serial Converters 通道/端口数量: 数据速率: 接口类型:USB, UART 工作电源电压:3.3 V, 5 V 最大工作温度:
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*