- 您现在的位置：买卖IC网 > PDF目录98166 > TB62209FG STEPPER MOTOR CONTROLLER, 1.8 A, PDSO38 PDF资料下载
参数资料
| 型号： | TB62209FG |
| 元件分类： | 运动控制电子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 1.8 A, PDSO38 |
| 封装： | 0.450 INCH, 0.65 MM PITCH, PLASTIC, HSOP-26/38 |
| 文件页数： | 34/51页 |
| 文件大小： | 501K |
| 代理商： | TB62209FG |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页当前第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页
TB62209FG
2005-03-02
4
3.
Current feedback circuit and current setting circuit
Function
The current setting circuit is used to set the reference voltage of the output current using the current
setting decoder.
The current feedback circuit is used to output to the output control circuit the relation between the
set current value and output current. This is done by comparing the reference voltage output to the
current setting circuit with the potential difference generated when current flows through the current
sense resistor connected between RS and VM.
The chopping waveform generator circuit to which CR is connected is used to generate clock used as
reference for the chopping frequency.
Note 1: RS COMP1: Compares the set current with the output current and outputs a signal when the output
current reaches the set current.
Note 2: RS COMP2: Compares the set current with the output current at the end of Fast mode during chopping.
Outputs a signal when the set current is below the output current.
Waveform shaping circuit
VM
RS
Vref
100％
85％
70％
50％
Chopping waveform
generator circuit
CR
VRS circuit 1
(detects
potential
difference
between
RS and VM)
RS COMP
circuit
1
(Note 1)
NF
(set current
reached signal)
VRS circuit 2
(detects
potential
difference
between
VM and RS)
RS COMP
circuit
2
(Note 2)
RNF
(set current
monitor signal)
<Use in FAST MODE>
<Use in Charge mode>
Output
control
circuit
Mixed
Decay
timing
circuit
Output stop signal (ALL OFF)
Chopping reference circuit
0
Current feedback circuit
Torque
control
circuit
Current setting
circuit
D/A circuit
TORQUE
0, 1
CURRENT
0-3
Decoder
Unit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Micro-step
current
setting
selector
circuit
4-bit
D/A
circuit
相关PDF资料 |
PDF描述 |
|---|---|
| TB62214FTG | STEPPER MOTOR CONTROLLER, 2 A, PQCC48 |
| TB62754AFNG | SWITCHING REGULATOR, PDSO20 |
| TB62756FUG | SWITCHING REGULATOR, 1430 kHz SWITCHING FREQ-MAX, PDSO6 |
| TB62757FUG | SWITCHING REGULATOR, 1430 kHz SWITCHING FREQ-MAX, PDSO6 |
| TB6512AFG | STEPPER MOTOR CONTROLLER, 0.12 A, PDSO24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TB62209FG(EL) | 功能描述:马达/运动/点火控制器和驱动器 Stepping Motor Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TB62209FG(O,EL) | 功能描述:马达/运动/点火控制器和驱动器 Stepping Motor PWM 40V 1.8A RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TB62209SN | 制造商:THOMAS & BETTS 功能描述: |
| TB622-100.0M | 制造商:Connor-Winfield 功能描述:OSC TCXO 100MHZ 3.3V SMD |
| TB-6221-01 | 功能描述:界面模块 SWITCH TERMINATION BRD 62P D-SUB FEMALE RoHS:否 制造商:4D Systems 产品:Serial Converters 通道/端口数量: 数据速率: 接口类型:USB, UART 工作电源电压:3.3 V, 5 V 最大工作温度: |
发布紧急采购，3分钟左右您将得到回复。