- 您现在的位置：买卖IC网 > PDF目录10750 > TC500IJE (Microchip Technology)IC ANALOG FRONT END 16BIT 16CDIP PDF资料下载
参数资料
| 型号： | TC500IJE |
| 厂商： | Microchip Technology |
| 文件页数： | 3/38页 |
| 文件大小： | 0K |
| 描述： | IC ANALOG FRONT END 16BIT 16CDIP |
| 标准包装： | 29 |
| 位数： | 16 |
| 通道数： | 1 |
| 功率（瓦特）： | 10mW |
| 电压 - 电源，模拟： | 5V |
| 电压 - 电源，数字： | 4.5 V ~ 7.5 V |
| 封装/外壳： | 16-CDIP（0.300"，7.62mm） |
| 供应商设备封装： | 16-CDIP |
| 包装： | 管件 |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
2008 Microchip Technology Inc.
DS21428E-page 11
TC500/A/510/514
5.0
TC500/A/510/514 CONVERTER
OPERATION
The TC500/A/510/514 incorporates an auto-zero and
Integrator phase in addition to the input signal Integrate
and reference De-integrate phases. The addition of
these phases reduce system errors, calibration steps
and shorten overrange recovery time. A typical
measurement cycle uses all four phases in the
following order:
1.
Auto-zero.
2.
Input signal integration.
3.
Reference de-integration.
4.
Integrator output zero.
The internal analog switch status for each of these
phases is summarized in Table 5-1. This table
references the Typical Application.
TABLE 5-1:
INTERNAL ANALOG GATE STATUS
5.1
Auto-zero Phase (AZ)
During this phase, errors due to buffer, integrator and
comparator offset voltages are nulled out by charging
CAZ (auto-zero capacitor) with a compensating error
voltage.
The external input signal is disconnected from the
internal circuitry by opening the two SWI switches. The
internal input points connect to analog common. The
reference capacitor is charged to the reference voltage
potential through SWR. A feedback loop, closed around
the integrator and comparator, charges the capacitor
(CAZ) with a voltage to compensate for buffer amplifier,
integrator and comparator offset voltages.
5.2
Analog Input Signal Integration
Phase (INT)
The TC5XX integrates the differential voltage between
the VIN+ and VIN– inputs. The differential voltage must
be within the device’s Common mode range VCMR. The
input signal polarity is normally checked via software at
the end of this phase: CMPTR = 1 for positive polarity;
CMPTR = 0 for negative polarity.
5.3
Reference Voltage De-integration
Phase (DINT)
The previously charged reference capacitor is
connected with the proper polarity to ramp the
integrator output back to zero. An externally-provided,
precision timer is used to measure the duration of this
phase. The resulting time measurement is proportional
to the magnitude of the applied input voltage.
5.4
Integrator Output Zero Phase (IZ)
This phase ensures the integrator output is at 0V when
the auto-zero phase is entered, and that only system
offset voltages are compensated. This phase is used at
the end of the reference voltage de-integration phase
and MUST be used for ALL TC5XX applications having
resolutions of 12-bits or more. If this phase is not used,
the value of the auto-zero capacitor (CAZ) must be
about 2 to 3 times the value of the integration capacitor
(CINT) to reduce the effects of charge sharing. The
integrator output zero phase should be programmed to
operate until the output of the comparator returns high.
The overall timing system is shown in Figure 5-1.
Conversion Phase
SWI
SWR+SWR-SWZ
SWR
SW1
SWIZ
Auto-zero (A = 0, B = 1)
—
Closed
—
Input Signal Integration (A = 1, B = 0)
Closed
—
Reference Voltage De-integration
(A =1, B = 1)
—
*
Closed
—
Closed
—
Integrator Output Zero (A = 0, B = 0)
—
Closed
* Assumes a positive polarity input signal. SW–RI would be closed for a negative input signal.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX919EUK+T | IC COMPARATOR BTR SOT23-5 |
| VI-J32-MY-F3 | CONVERTER MOD DC/DC 15V 50W |
| VI-B6D-MX-F1 | CONVERTER MOD DC/DC 85V 75W |
| VI-J32-MY-F2 | CONVERTER MOD DC/DC 15V 50W |
| VI-B64-MX-F4 | CONVERTER MOD DC/DC 48V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TC500IOE | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Precision Analog Front Ends with Dual Slope ADC |
| TC500IOE713 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Precision Analog Front Ends with Dual Slope ADC |
| TC500IOG | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Precision Analog Front Ends with Dual Slope ADC |
| TC500IOG713 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Precision Analog Front Ends with Dual Slope ADC |
| TC500IOI | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Precision Analog Front Ends with Dual Slope ADC |
发布紧急采购，3分钟左右您将得到回复。