- 您现在的位置：买卖IC网 > PDF目录10750 > TC500IJE (Microchip Technology)IC ANALOG FRONT END 16BIT 16CDIP PDF资料下载
参数资料
| 型号： | TC500IJE |
| 厂商： | Microchip Technology |
| 文件页数： | 5/38页 |
| 文件大小： | 0K |
| 描述： | IC ANALOG FRONT END 16BIT 16CDIP |
| 标准包装： | 29 |
| 位数： | 16 |
| 通道数： | 1 |
| 功率（瓦特）： | 10mW |
| 电压 - 电源，模拟： | 5V |
| 电压 - 电源，数字： | 4.5 V ~ 7.5 V |
| 封装/外壳： | 16-CDIP（0.300"，7.62mm） |
| 供应商设备封装： | 16-CDIP |
| 包装： | 管件 |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
2008 Microchip Technology Inc.
DS21428E-page 13
TC500/A/510/514
6.0
ANALOG SECTION
6.1
Differential Inputs (VIN+, VIN–)
The TC5XX operates with differential voltages within
the input amplifier Common mode range. The amplifier
Common mode range extends from 1.5V below
positive supply to 1.5V above negative supply. Within
this Common mode voltage range, Common mode
rejection is typically 80 dB. Full accuracy is maintained,
however, when the inputs are no less than 1.5V from
either supply.
The integrator output also follows the Common mode
voltage. The integrator output must not be allowed to
saturate. A worst-case condition exists, for example,
when a large, positive Common mode voltage, with a
near full-scale negative differential input voltage, is
applied. The negative input signal drives the integrator
positive when most of its swing has been used up by
the positive Common mode voltage. For these critical
applications, the integrator swing can be reduced. The
integrator output can swing within 0.9V of either supply
without loss of linearity.
6.2
Analog Common
Analog common is used as VIN return during system
zero and reference de-integrate. If VIN– is different from
analog common, a Common mode voltage exists in the
system. This signal is rejected by the excellent CMR of
the converter. In most applications, VIN– will be set at a
fixed known voltage (i.e., power supply common). A
Common mode voltage will exist when VIN– is not
connected to analog common.
6.3
Differential Reference
(VREF+, VREF–)
The reference voltage can be anywhere within 1V of
the power supply voltage of the converter. Rollover
error is caused by the reference capacitor losing or
gaining charge due to stray capacitance on its nodes.
The difference in reference for (+) or (-) input voltages
will cause a rollover error. This error can be minimized
by using a large reference capacitor in comparison to
the stray capacitance.
6.4
Phase Control Inputs (A, B)
The A, B unlatched logic inputs select the TC5XX
operating phase. The A, B inputs are normally driven
by a microprocessor I/O port or external logic.
6.5
Comparator Output
By monitoring the comparator output during the fixed
signal integrate time, the input signal polarity can be
determined by the microprocessor controlling the
conversion. The comparator output is high for positive
signals and low for negative signals during the signal
integrate phase (see Figure 6-1).
During
the
reference
de-integrate
phase,
the
comparator output will make a high-to-low transition as
the integrator output ramp crosses zero. The transition
is used to signal the processor that the conversion is
complete.
The internal comparator delay is 2 μs, typically.
Figure 6-1 shows the comparator output for large
positive and negative signal inputs. For signal inputs at
or near zero volts, however, the integrator swing is very
small. If Common mode noise is present, the
comparator can switch several times during the
beginning of the signal integrate period. To ensure that
the polarity reading is correct, the comparator output
should be read and stored at the end of the signal
integrate phase.
The comparator output is undefined during the auto-
zero phase and is used to time the integrator output
zero phase. (See Section 8.6 “Integrator Output Zero
FIGURE 6-1:
Comparator Output.
Integrator
Output
Zero
Crossing
Comparator
Output
Reference
Signal
Integrate
Integrator
Output
Zero
Crossing
Comparator
Output
Reference
Deintegrate
Signal
Integrate
B. Negative Input Signal
A. Positive Input Signal
De-integrate
相关PDF资料 |
PDF描述 |
|---|---|
| MAX919EUK+T | IC COMPARATOR BTR SOT23-5 |
| VI-J32-MY-F3 | CONVERTER MOD DC/DC 15V 50W |
| VI-B6D-MX-F1 | CONVERTER MOD DC/DC 85V 75W |
| VI-J32-MY-F2 | CONVERTER MOD DC/DC 15V 50W |
| VI-B64-MX-F4 | CONVERTER MOD DC/DC 48V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TC500IOE | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Precision Analog Front Ends with Dual Slope ADC |
| TC500IOE713 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Precision Analog Front Ends with Dual Slope ADC |
| TC500IOG | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Precision Analog Front Ends with Dual Slope ADC |
| TC500IOG713 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Precision Analog Front Ends with Dual Slope ADC |
| TC500IOI | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Precision Analog Front Ends with Dual Slope ADC |
发布紧急采购，3分钟左右您将得到回复。