- 您现在的位置：买卖IC网 > PDF目录69480 > TC642EUA BRUSHLESS DC MOTOR CONTROLLER, PDSO8 PDF资料下载
参数资料
| 型号： | TC642EUA |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| 封装： | PLASTIC, MSOP-8 |
| 文件页数： | 24/28页 |
| 文件大小： | 485K |
| 代理商： | TC642EUA |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页
2002 Microchip Technology Inc.
DS21444C-page 5
TC642
3.0
DETAILED DESCRIPTION
3.1
PWM
The PWM circuit consists of a ramp generator and
threshold detector. The frequency of the PWM is deter-
mined by the value of the capacitor connected to the CF
input. A frequency of 30 Hz is recommended
(CF = 1 F). The PWM is also the time base for the
Start-up Timer (see Section 3.4, “Start-Up Timer”). The
PWM voltage control range is 1.25V to 2.65V (typical)
for 0% to 100% output duty cycle.
3.2
FAULT Output
The TC642 detects faults in two ways.
First, pulses appearing at SENSE due to the PWM
turning on are blanked, with the remaining pulses
filtered by a missing pulse detector. If consecutive
pulses are not detected for 32 PWM cycles (
1 Sec if
CF = 1 F), the Diagnostic Timer is activated, and VOUT
is driven high continuously for three PWM cycles
(
100 msec if CF = 1 F). If a pulse is not detected
within this window, the Start-up Timer is triggered (see
Section 3.4). This should clear a transient fault condi-
tion. If the missing pulse detector times out again, the
PWM is stopped and FAULT goes low. When FAULT is
activated due to this condition, the device is latched in
shutdown mode and will remain off indefinitely.
The TC642 may be configured to continuously attempt
fan restarts, if so desired.
Continuous restart mode is enabled by connecting the
FAULT output to VMIN through a 0.01 F capacitor, as
shown in Figure 3-1. When connected in this manner,
the TC642 automatically attempts to restart the fan
every time a fault condition occurs. When the FAULT
output is driven low, the VMIN input is momentarily
pulled below VSHDN, initiating a reset and clearing the
fault condition. Normal fan start-up is then attempted as
previously described. The FAULT output may be
connected to external logic (or the interrupt input of a
microcontroller) to shut the TC642 down if multiple fault
pulses are detected at approximately one second
intervals. Diode D1, capacitor C1 and resistors R5 and
R6 are provided to ensure fan restarts are the result of
a fan fault and not an over-temperature fault. A CMOS
logic OR gate may be substituted for these
components, if available.
FIGURE 3-1:
Fan Fault Output Circuit.
Note:
At this point, action must be taken to restart
the fan by momentarily pulling VMIN below
VSHDN, or cycling system power. In either
case, the fan cannot remain disabled due
to a fault condition, as severe system dam-
age could result. If the fan cannot be
restarted, the system should be shut down.
FAULT
SENSE
R3
R1
R5
10k
D1
R4
GND
From
System
Shutdown
Controller
(Optional)
*The parallel combination of R3 and R4 must be >10 k.
Q1
+12V
+5V
VDD
VIN
VMIN
VOUT
RBASE
R6
1k
VDD
RSENSE
CSENSE
CF
1
F
CF
TC642
Fan
CB
0.01
F
1
8
6
7
5
4
2
3
From
Temp
Sensor
+5V
0.01
F
1
0
TC642
RESET
Fault
Detected
C1
Q2
相关PDF资料 |
PDF描述 |
|---|---|
| TC642EUA713 | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| TC642EOA713 | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| TC646EOA | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| TC646VUA | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| TC646VOA713G | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TC642EUA713 | 功能描述:马达/运动/点火控制器和驱动器 w/Fault Dtct RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TC642EV | 功能描述:电源管理IC开发工具 For TC642/6/7/8/9 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| TC642EV | 制造商:Microchip Technology Inc 功能描述:Tools Development kit For Use |
| TC642VOA | 功能描述:马达/运动/点火控制器和驱动器 w/Fault Dtct RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TC642VOA713 | 功能描述:马达/运动/点火控制器和驱动器 w/Fault Dtct RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。