- 您现在的位置：买卖IC网 > PDF目录69480 > TC642VUA BRUSHLESS DC MOTOR CONTROLLER, PDSO8 PDF资料下载
参数资料
| 型号： | TC642VUA |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| 封装： | PLASTIC, MSOP-8 |
| 文件页数： | 26/28页 |
| 文件大小： | 485K |
| 代理商： | TC642VUA |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页
2002 Microchip Technology Inc.
DS21444C-page 7
TC642
4.0
SYSTEM BEHAVIOR
The flowcharts describing the TC642’s behavioral
algorithm are shown in Figure 4-1. They can be
summarized as follows:
4.1
Power-Up
(1) Assuming the device is not being held in shutdown
mode (VMIN > VREL)…
(2) Turn VOUT output on for 32 cycles of the PWM
clock. This ensures that the fan will start from a
dead stop.
(3) During this Start-up Timer, if a fan pulse is
detected, branch to Normal Operation; if none are
received…
(4) Activate the 32-cycle Start-up Timer one more
time and look for a fan pulse; if a fan pulse is
detected, proceed to Normal Operation; if none
are received…
(5) Proceed to Fan Fault.
(6) End.
4.2
Normal Operation
Normal Operation is an endless loop which may only
be exited by entering shutdown mode or Fan Fault. The
loop can be thought of as executing at the frequency of
the oscillator and PWM.
(1) Reset the missing pulse detector.
(2) Is TC642 in shutdown? If so…
a. VOUT duty cycle goes to zero.
b. FAULT is disabled.
c. Exit the loop and wait for VMIN > VREL to
resume
operation
(indistinguishable
from
power-up).
(3) If an over-temperature fault occurs (VIN > VOTF),
activate FAULT; release FAULT when VIN < VOTF.
(4) Drive VOUT to a duty cycle proportional to the
greater of VIN and VMIN on a cycle by cycle basis.
(5) If a fan pulse is detected, branch back to the start
of the loop (1).
(6) If the missing pulse detector times out …
(7) Activate the 3-cycle Diagnostic Timer and look for
pulses; if a fan pulse is detected, branch back to
the start of the loop (1); if none are received…
(8) Activate the 32-cycle Start-up Timer and look for
pulses; if a fan pulse is detected, branch back to
the start of the loop (1); if none are received…
(9) Quit Normal Operation and go to Fan Fault.
(10) End.
4.3
Fan Fault
Fan fault is an infinite loop wherein the TC642 is
latched in shutdown mode. This mode can only be
released by a reset (i.e., VMIN being brought below
VSHDN, then above VREL, or by power-cycling).
(1) While in this state, FAULT is latched on (low) and
the VOUT output is disabled.
(2) A reset sequence applied to the VMIN pin will exit
the loop to Power-Up.
(3) End.
相关PDF资料 |
PDF描述 |
|---|---|
| TC642EUA | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| TC642EUA713 | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| TC642EOA713 | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| TC646EOA | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| TC646VUA | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TC642VUA713 | 功能描述:马达/运动/点火控制器和驱动器 w/Fault Dtct RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TC643VPA | 功能描述:IC FAN/MOTOR DRIVER 8-DIP RoHS:否 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 产品变化通告:ATA683(3,4)PLQW Obsolescence 09/Aug/2012 标准包装:1 系列:- 应用:DC 电机控制器，无刷（BLDC），3 相 评估套件:可供 输出数:1 电流 - 输出:100mA 电压 - 负载:5.25 V ~ 20 V 电源电压:5.25 V ~ 20 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-VQFN（7x7） 包装:剪切带 (CT) 其它名称:ATA6833-PLQWCT |
| TC643VUA | 功能描述:IC FAN/MOTOR DRIVER 8-MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 产品变化通告:ATA683(3,4)PLQW Obsolescence 09/Aug/2012 标准包装:1 系列:- 应用:DC 电机控制器，无刷（BLDC），3 相 评估套件:可供 输出数:1 电流 - 输出:100mA 电压 - 负载:5.25 V ~ 20 V 电源电压:5.25 V ~ 20 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-VQFN（7x7） 包装:剪切带 (CT) 其它名称:ATA6833-PLQWCT |
| TC644 | 制造商:Datak Corporation 功能描述:CIGARETTE LIGHTER, AUTOMOTIVE POWER ACCESSORIES, CIGARETTE LIGHTER PLUG |
| TC644B | 制造商:Datak Corporation 功能描述:Cigarette Lighter Plug |
发布紧急采购，3分钟左右您将得到回复。