- 您现在的位置：买卖IC网 > PDF目录98171 > TC649VOATR BRUSHLESS DC MOTOR CONTROLLER, PDSO8 PDF资料下载
参数资料
| 型号： | TC649VOATR |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| 封装： | 0.150 INCH, PLASTIC, SOIC-8 |
| 文件页数： | 2/28页 |
| 文件大小： | 478K |
| 代理商： | TC649VOATR |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
TC649
DS21449C-page 10
2002 Microchip Technology Inc.
5.1
Temperature Sensor Design
The temperature signal connected to VIN must output a
voltage in the range of 1.25V to 2.65V (typical) for 0%
to 100% of the temperature range of interest. The
circuit in Figure 5-2 illustrates a convenient way to
provide this signal.
FIGURE 5-2:
Temperature Sensing
Circuit.
Figure 5-2 shows a simple temperature dependent
voltage divider circuit. RT1 is a conventional NTC ther-
mistor, while R1 and R2 are standard resistors. The
supply voltage, VDD, is divided between R2 and the
parallel combination of RT1 and R1. For convenience,
the parallel combination of RT1 and R1 will be referred
to as RTEMP. The resistance of the thermistor at various
temperatures is obtained from the manufacturer’s
specifications. Thermistors are often referred to in
terms of their resistance at 25°C.
Generally, the thermistor shown in Figure 5-2 is a non-
linear device with a negative temperature coefficient
used to linearize the thermistor temperature response
and R2 is used to produce a positive temperature
coefficient at the VIN node. As an added benefit, this
configuration produces an output voltage delta of 1.4V,
which is well within the range of the VC(SPAN)
specification of the TC649. A 100 k
NTC thermistor is
selected for this application in order to keep IDIV at a
minimum.
For the voltage range at VIN to be equal to 1.25V to
2.65V, the temperature range of this configuration is
0°C to 50°C. If a different temperature range is required
from this circuit, R1 should be chosen to equal the
resistance value of the thermistor at the center of this
new temperature range. It is suggested that a maxi-
mum temperature range of 50°C be used with this cir-
cuit due to thermistor linearity limitations. With this
change, R2 is adjusted according to the following
equations:
EQUATION
More information about thermistors may be obtained
from AN679, “Temperature Sensing Technologies”,
and
AN685,
“Thermistors
in
Single
Supply
Temperature Sensing Circuit”, which can be down-
loaded
from
Microchip’s
website
at
www.microchip.com.
5.2
Auto-Shutdown Temperature
Design
A voltage divider on VAS sets the temperature at which
the part is automatically shut down if the sensed tem-
perature at VIN drops below the set temperature at VAS
(i.e. VIN < VAS). As with the VIN input, 1.25V to 2.65V
(typ.) corresponds to the temperature range of interest
from T1 to T2, respectively. Assuming that the temper-
ature sensor network designed above is linearly related
to temperature, the shutdown temperature TAS is
related to T2 and T1 by:
EQUATION
For example, if 1.25V and 2.65V at VIN corresponds to
a temperature range of T1 = 0°C to T2 = 125°C, and the
auto-shutdown temperature desired is 25°C, then VAS
voltage is:
EQUATION
divider, as is shown in Figure 5-3.
R2 = 23.2 k
R1 =100 k
RT1
NTC
Thermistor
100 k
@ 25C
IDIV
VIN
VDD
VDD x R2
RTEMP (T1) + R2
= V(T1)
RTEMP (T2) + R2
= V(T2)
VDD x R2
Where T1 and T2 define the temperature range of the
circuit. RTEMP is the parallel equivalent of the
thermistor and R1 at those temperatures.
2.65V - 1.25V
T2 - T1
=
VAS - 1.25
TAS - T1
VAS - 1.25
VAS =
(
(TAS - T1) + 1.25
1.4V )
T2 - T1
VAS =
(25 - 0) + 1.25 = 1.53V
1.4V
(125 - 0)
相关PDF资料 |
PDF描述 |
|---|---|
| TC649EUATR | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| TC655EUNTR | BRUSHLESS DC MOTOR CONTROLLER, PDSO10 |
| TC655EUN | BRUSHLESS DC MOTOR CONTROLLER, PDSO10 |
| TC654EUNTR | BRUSHLESS DC MOTOR CONTROLLER, PDSO10 |
| TC665EUN | BRUSHLESS DC MOTOR CONTROLLER, PDSO10 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TC649VPA | 功能描述:马达/运动/点火控制器和驱动器 Shtdn & Fault Dtct RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TC649VUA | 功能描述:马达/运动/点火控制器和驱动器 Shtdn & Fault Dtct RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TC649VUATR | 功能描述:马达/运动/点火控制器和驱动器 Shtdn & Fault Dtct RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TC6-4A11 | 制造商:FERROXCUBE 制造商全称:Ferroxcube International Holding B.V. 功能描述:Ferrite toroids |
| TC6-4C65 | 制造商:FERROXCUBE 制造商全称:Ferroxcube International Holding B.V. 功能描述:Ferrite toroids |
发布紧急采购，3分钟左右您将得到回复。