- 您现在的位置：买卖IC网 > PDF目录98171 > TC649VOATR BRUSHLESS DC MOTOR CONTROLLER, PDSO8 PDF资料下载
参数资料
| 型号： | TC649VOATR |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| 封装： | 0.150 INCH, PLASTIC, SOIC-8 |
| 文件页数： | 7/28页 |
| 文件大小： | 478K |
| 代理商： | TC649VOATR |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
2002 Microchip Technology Inc.
DS21449C-page 15
TC649
5.6
Latch-up Considerations
As with any CMOS IC, the potential exists for latch-up
if signals are applied to the device which are outside
the power supply range. This is of particular concern
during power-up if the external circuitry (such as the
sensor network, VAS divider or shutdown circuit) are
powered by a supply different from that of the TC649.
Care should be taken to ensure that the TC649’s VDD
supply powers up first. If possible, the networks
attached to VIN and VAS should connect to the VDD sup-
ply at the same physical location as the IC itself. Even
if the IC and any external networks are powered by the
same supply, physical separation of the connecting
points can result in enough parasitic capacitance and/
or inductance in the power supply connections to delay
one power supply “routing” versus another.
5.7
Power Supply Routing and
Bypassing
Noise present on the VIN and VAS inputs may cause
erroneous operation of the FAULT output. As a result,
these inputs should be bypassed with a 0.01 F
capacitor mounted as close to the package as possible.
This is especially true of VIN, which is usually drive from
a high impedance source (such as a thermistor). Addi-
tionally, the VDD input should be bypassed with a 1 F
capacitor with grounds being kept as short as possible.
To keep fan noise off the TC649 ground pin, individual
ground returns for the TC649 and the low side of the
fan current sense resistor should be used.
Design Example
Step 1. Calculate R1 and R2 based on using an NTC
having a resistance of 10 k
at TMIN (25°C)
and 4.65 k
R1 = 20.5 k
R2 = 3.83 k
Step 2. Set auto-shutdown Level.
VAS = 1.8V.
Limit the divider current to 100 A
R5 = 33 k
R6 = 18 k
Step 3. Design the output circuit.
Maximum fan motor current = 250 mA.
Q1 beta is chosen at 50 from which
R7 = 800 .
FIGURE 5-9:
Design Example.
FAULT
SENSE
NTC
10 k
@ 25C
R1
20.5 k
R2
3.83 k
R5
33 k
R7
800
GND
RESET
Shutdown
(Optional)
Q1
+12V
+5V
VDD
VIN
VAS
VOUT
RSENSE
2.2
CSENSE
0.1 F
C1
1 F
CF
TC649
Fan
Fan Fault
CB
0.01 F
CB
0.01 F
CB
1 F
1
8
4
6
7
5
2
3
R6
18 k
Open-
Drain
Device
相关PDF资料 |
PDF描述 |
|---|---|
| TC649EUATR | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| TC655EUNTR | BRUSHLESS DC MOTOR CONTROLLER, PDSO10 |
| TC655EUN | BRUSHLESS DC MOTOR CONTROLLER, PDSO10 |
| TC654EUNTR | BRUSHLESS DC MOTOR CONTROLLER, PDSO10 |
| TC665EUN | BRUSHLESS DC MOTOR CONTROLLER, PDSO10 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TC649VPA | 功能描述:马达/运动/点火控制器和驱动器 Shtdn & Fault Dtct RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TC649VUA | 功能描述:马达/运动/点火控制器和驱动器 Shtdn & Fault Dtct RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TC649VUATR | 功能描述:马达/运动/点火控制器和驱动器 Shtdn & Fault Dtct RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TC6-4A11 | 制造商:FERROXCUBE 制造商全称:Ferroxcube International Holding B.V. 功能描述:Ferrite toroids |
| TC6-4C65 | 制造商:FERROXCUBE 制造商全称:Ferroxcube International Holding B.V. 功能描述:Ferrite toroids |
发布紧急采购，3分钟左右您将得到回复。