参数资料
型号: TC654EUNTR
元件分类: 运动控制电子
英文描述: BRUSHLESS DC MOTOR CONTROLLER, PDSO10
封装: PLASTIC, MSOP-10
文件页数: 8/36页
文件大小: 706K
代理商: TC654EUNTR
TC654/TC655
DS21734A-page 16
2002 Microchip Technology Inc.
The data on the line must be changed during the LOW
period of the clock signal. There is one clock pulse per
bit of data. Each data transfer is initiated with a START
condition and terminated with a STOP condition. The
number of the data bytes transferred between the
START and STOP conditions is determined by the
master device and is unlimited.
5.1.7
ACKNOWLEDGE (ACK)
Each receiving device, when addressed, is obliged to
generate an acknowledge bit after the reception of
each byte. The master device must generate an extra
clock pulse, which is associated with this acknowledge
bit.
The device that acknowledges has to pull down the
SDA line during the acknowledge clock pulse in such a
way that the SDA line is stable LOW during the HIGH
period of the acknowledge related clock pulse. Setup
and hold times must be taken into account. During
reads, a master device must signal an end of data to
the slave by not generating an acknowledge bit on the
last byte that has been clocked out of the slave. In this
case, the slave (TC654/TC655) will leave the data line
HIGH to enable the master device to generate the
STOP condition.
5.2
SMBus Protocols
The TC654/TC655 devices communicate with three
standard SMBus protocols. These are the write byte,
read byte and receive byte. The receive byte is a short-
ened method for reading from, or writing to, a register
which had been selected by the previous read or write
command. These transmission protocols are shown in
Figures 5-1, 5-2 and 5-3.
FIGURE 5-1:
SMBus Protocol: Write Byte Format.
FIGURE 5-2:
SMBus Protocol: Read Byte Format.
FIGURE 5-3:
SMBus Protocol: Receive Byte Format.
S
ADDRESS
WR
ACK
COMMAND
ACK
DATA
ACK
P
7 Bits
8 Bits
Slave Address
Command Byte: selects
which register you are
writing to.
Data Byte: data goes
into the register set
by the command byte.
S
ADDRESS
WR
ACK
COMMAND
ACK
7 Bits
8 Bits
Slave Address
Command Byte: selects
which register you are
writing to.
S
ADDRESS
RD
ACK
DATA
NACK
P
7 Bits
8 Bits
Slave Address:
repeated due to change
in data flow direction.
Data Byte: reads from
the register set by the
command byte.
S
ADDRESS
RD
ACK
DATA
NACK
P
7 Bits
8 Bits
Slave Address
Data Byte: reads data from
the register commanded by
the last Read Byte or Write
Byte transmission
S = Start Condition
P = Stop Condition
Shaded = Slave Transmission
ACK = Acknowledge = 0
NACK = Not Acknowledged = 1
WR = Write = 0
RD = Read = 1
相关PDF资料
PDF描述
TC665EUN BRUSHLESS DC MOTOR CONTROLLER, PDSO10
TC7106ARCPLIJL 1-CH DUAL-SLOPE ADC, ACCESS, PDIP40
TC7106CPLIJL 1-CH DUAL-SLOPE ADC, ACCESS, PDIP40
TC7107ARCPLIJL 1-CH DUAL-SLOPE ADC, ACCESS, PDIP40
TC7106ACPLIJL 1-CH DUAL-SLOPE ADC, PDIP40
相关代理商/技术参数
参数描述
TC655 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Dual SMBus⑩ PWM Fan Speed Controllers With Fan Fault Detection
TC655EUN 功能描述:软开关 PWM 控制器 Dual RoHS:否 制造商:Fairchild Semiconductor 输出端数量: 输出电流: 开关频率: 工作电源电压:30 V 电源电流: 最大工作温度:+ 105 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel
TC655EUNTR 功能描述:软开关 PWM 控制器 Dual RoHS:否 制造商:Fairchild Semiconductor 输出端数量: 输出电流: 开关频率: 工作电源电压:30 V 电源电流: 最大工作温度:+ 105 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel
TC65A 制造商:CDE 制造商全称:Cornell Dubilier Electronics 功能描述:Axial Leaded Aluminum Electrolytic Capacitors
TC65I 制造商:CINTERION 功能描述:MODULE GSM/GPRS QUADBAND + JAVA TC65I 制造商:CINTERION 功能描述:MOD, GSM / GPRS, QUAD BAND, TCP/IP 制造商:CINTERION 功能描述:MOD, GSM / GPRS, QUAD BAND, I2C, SPI, USB, TCP/IP; No. of Channels:4; Supply Voltage Min:3.2V; Supply Voltage Max:4.5V; Frequency RF:1900MHz; Module Interface:I2C, SPI, USB; RF Coax Type:1.9 GHz; Supply Voltage Range:3.2V to 4.5V ;RoHS Compliant: Yes