- 您现在的位置：买卖IC网 > PDF目录20139 > TC7107CLW713 (Microchip Technology)IC ADC 3 1/2DGT LED DVR 44-PLCC PDF资料下载
参数资料
| 型号： | TC7107CLW713 |
| 厂商： | Microchip Technology |
| 文件页数： | 14/34页 |
| 文件大小： | 0K |
| 描述： | IC ADC 3 1/2DGT LED DVR 44-PLCC |
| 标准包装： | 500 |
| 显示器类型： | LED |
| 配置： | 7 段显示 |
| 数字或字符： | A/D，3.5 位数字 |
| 电流 - 电源： | 800µA |
| 电源电压： | 5V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-LCC（J 形引线） |
| 供应商设备封装： | 44-PLCC |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
TC7106/A/TC7107/A
7.0
COMPONENT VALUE
7.4
Integrating Resistor (R INT )
SELECTION
7.1 Auto-Zero Capacitor (C AZ )
The C AZ capacitor size has some influence on system
noise. A 0.47 μF capacitor is recommended for 200 mV
full scale applications where 1LSB is 100 μV. A
0.047 μF capacitor is adequate for 2.0V full scale
applications. A mylar type dielectric capacitor is
The input buffer amplifier and integrator are designed
with class A output stages. The output stage idling
current is 100 μA. The integrator and buffer can supply
20 μA drive currents with negligible linearity errors.
R INT is chosen to remain in the output stage linear drive
region, but not so large that printed circuit board
leakage currents induce errors. For a 200 mV full scale,
R INT is 47 k Ω . 2.0V full scale requires 470 k Ω .
adequate.
7.2 Reference Voltage Capacitor
(C REF )
The reference voltage used to ramp the integrator out-
put voltage back to zero during the reference integrate
TABLE 7-1:
Component
Value
COMPONENT VALUES AND
NOMINAL FULL SCALE
VOLTAGE
Nominal Full Scale Voltage
200.0 mV 2.000V
cycle is stored on C REF . A 0.1 μF capacitor is
acceptable when V IN - is tied to analog common. If a
large Common mode voltage exists (V REF - – analog
common) and the application requires 200 mV full
C AZ
R INT
C INT
0.47 μF
47 k Ω
0.22 μF
0.047 μF
470 k Ω
0.22 μF
scale, increase C REF to 1.0 μF. Rollover error will be
held to less than 1/2 count. A mylar dielectric capacitor
is adequate.
Note:
7.5
F OSC = 48 kHz (3 readings per sec).
Oscillator Components
7.3
Integrating Capacitor (C INT )
R OSC (Pin 40 to Pin 39) should be 100 k Ω . C OSC is
selected using the equation:
C INT should be selected to maximize the integrator
F OSC = 0.45
output voltage swing without causing output saturation.
Due to the TC7106A/TC7107A superior temperature
coefficient specification, analog common will normally
supply the differential voltage reference. For this case,
a ±2V full scale integrator output swing is satisfactory.
For 3 readings/second (F OSC = 48 kHz), a 0.22 μF
EQUATION 7-2:
Where:
F OSC = 48 kHz
RC
value is suggested. If a different oscillator frequency is
C OSC
=
100 pF
used, C INT must be changed in inverse proportion to
maintain the nominal ±2V integrator swing.
An exact expression for C INT is:
EQUATION 7-1:
Note that F OSC is divided by four to generate the
TC7106A internal control clock. The backplane drive
signal is derived by dividing F OSC by 800.
To achieve maximum rejection of 60 Hz noise pickup,
( 4000 ) ? ? ? ? ? ? ? ?
1 V FS
F OSC R INT
Where:
C INT
------------- -----------
= ------------------------------------------------------
V INT
the signal integrate period should be a multiple of
60 Hz. Oscillator frequencies of 240 kHz, 120 kHz,
80 kHz, 60 kHz, 48 kHz, 40 kHz, etc. should be
selected. For 50 Hz rejection, oscillator frequencies of
200 kHz, 100 kHz, 66-2/3 kHz, 50 kHz, 40 kHz, etc.
F OSC
V FS
=
=
Clock Frequency at Pin 38
Full Scale Input Voltage
would be suitable. Note that 40 kHz (2.5 readings/
second) will reject both 50 Hz and 60 Hz.
R INT
V INT
=
=
Integrating Resistor
Desired Full Scale Integrator Output
7.6
Reference Voltage Selection
Swing
A full scale reading (2000 counts) requires the input
signal be twice the reference voltage.
C INT must have low dielectric absorption to minimize
rollover error. A polypropylene capacitor is
recommended.
Required Full Scale Voltage*
200.0 mV
2.000V
* V FS = 2V REF
V REF
100.0 mV
1.000V
DS21455D-page 14
? 2008 Microchip Technology Inc.
相关PDF资料 |
PDF描述 |
|---|---|
| IDT71V65903S85PF | IC SRAM 9MBIT 85NS 100TQFP |
| TC7135CBU713 | IC ADC 4 1/2DGT 64-MQFP |
| ISL9008AIRUNZ-T | IC REG LDO 3.3V .15A 6-UTDFN |
| GBB11DHAS | CONN EDGECARD 22POS R/A .050 SLD |
| IDT71V65903S80PFI8 | IC SRAM 9MBIT 80NS 100TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TC7107CPL | 功能描述:LED显示驱动器 w/LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| TC7107CPL | 制造商:Microchip Technology Inc 功能描述:Leaded Process Compatible:No |
| TC7107CPL | 制造商:Microchip Technology Inc 功能描述:3.5 DIGIT ADC CMOS 7107 DIP40 制造商:Microchip Technology Inc 功能描述:3.5 DIGIT ADC, CMOS, 7107, DIP40 制造商:Microchip Technology Inc 功能描述:3.5 DIGIT ADC, CMOS, 7107, DIP40; Resolution (Bits):3.5bit; Supply Voltage Type:Single; Supply Voltage Max:5V; Supply Current:800A; Digital IC Case Style:DIP; No. of Pins:40; Input Channel Type:Differential; Data Interface:Parallel;;RoHS Compliant: Yes |
| TC7107IJL | 功能描述:LED显示驱动器 3-1/2 Digit A/D w/ LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| TC7107IPL | 功能描述:LED显示驱动器 w/LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。