参数资料
型号: TC7652CPA
厂商: Microchip Technology
文件页数: 15/16页
文件大小: 0K
描述: IC OPAMP CHOPPER STAB LN 8DIP
标准包装: 60
放大器类型: 断路器(零漂移)
电路数: 1
转换速率: 1 V/µs
增益带宽积: 400kHz
电流 - 输入偏压: 30pA
电压 - 输入偏移: 2000µV
电流 - 电源: 1mA
电压 - 电源,单路/双路(±): 5 V ~ 16 V,±2.5 V ~ 8 V
工作温度: 0°C ~ 70°C
安装类型: 通孔
封装/外壳: 8-DIP(0.300",7.62mm)
供应商设备封装: 8-PDIP
包装: 管件
产品目录页面: 680 (CN2011-ZH PDF)
其它名称: 158-1136
158-1136-ND
TC7652
DS21464B-page 8
2002 Microchip Technology Inc.
4.6
Pin Compatibility
Where possible, the 8-pin device pinout conforms to
such industry standards as the LM101 and LM741. Null
storing external capacitors connect to Pins 1 and 8,
which are usually for offset null or compensation capac-
itors. Output clamp (Pin 5) is similarly used. For OP05
and OP07 devices, replacement of the offset null
potentiometer (connected between Pins 1 and 8 and
VDD by two capacitors from those pins to VSS) provides
compatibility. Replacing the compensation capacitor
between Pins 1 and 8 by two capacitors to VSS is
required. The same operation (with the removal of any
connection to Pin 5) works for LM101,
A748 and sim-
ilar parts.
Because NC pins provide guarding between input and
other pins, the 14-pin device pinout conforms closely to
the LM108. Because this device does not use any extra
pins and does not provide offset nulling (but requires a
compensation capacitor), some layout changes are
necessary to convert to the TC7652.
4.7
Some Applications
Figures 4-2 and 4-3 show basic inverting and nonin-
verting amplifier circuits using the output clamping cir-
cuit to enhance overload recovery performance. The
only limitations on replacing other op amps with the
TC7652 are supply voltage (±8V maximum) and output
drive capability (10k
load for full swing). Overcome
these limitations with a booster circuit (Figure 4-4) to
combine output capabilities of the LM741 (or other
standard device) with input capabilities of the TC7652.
These two form a composite device, therefore, when
adding the feedback network, the monitor loop gains
stability.
FIGURE 4-2:
NONINVERTING
AMPLIFIER WITH
OPTIONAL CLAMP
FIGURE 4-3:
INVERTING AMPLIFIER
WITH OPTIONAL CLAMP
FIGURE 4-4:
USING 741 TO BOOST
OUTPUT DRIVE
CAPABILITY
Figure 4-5 shows the clamp circuit of a zero offset com-
parator. Because the clamp circuit requires the invert-
ing input to follow the input signal, problems with a
chopper stabilized op amp are avoided. The threshold
input must tolerate the output clamp current
≈VIN/R
without disrupting other parts of the system.
Figure 4-6 shows how the TC7652 can offset null high
slew rate and wideband amplifiers.
Mixing the TC7652 with circuits operating at ±15V
requires a lower supply voltage divider with the TC7660
voltage converter circuit operated "backwards." Figure
4-7 shows an approximate connection.
FIGURE 4-5:
LOW OFFSET
COMPARATOR
TC7652
+
Output
Clamp
Input
0.1F
R2
R1
R3
0.1F
+
Output
Input
R2
R1
Clamp
0.1F
TC7652
+
+
+15V
-15V
-7.5V
0.1
F
In
Out
-7.5V
0.1
F
10k
TC7652
741
TC7652
+
VOUT
Clamp
VIN
0.1F
200k
to 2m
VTH
相关PDF资料
PDF描述
PTVS5V0S1UR,115 TVS 400W UNIDIR 5V SOD-123W
V150CH8 VARISTOR 150V 250A 3J SMD CH T/R
929852-01-20-30 CONN RCPT 40POS DUAL .100" GO
V120CH8 VARISTOR 120V 250A 2J SMD CH T/R
TC913BCOA IC OPAMP DUAL AUTO ZERO 8SOIC
相关代理商/技术参数
参数描述
TC7652CPD 功能描述:运算放大器 - 运放 Low Noise RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比(最小值):63 dB 输入补偿电压:1 mV 输入偏流(最大值):10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel
TC7652IJA 功能描述:运算放大器 - 运放 Low Noise RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比(最小值):63 dB 输入补偿电压:1 mV 输入偏流(最大值):10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel
TC7652IJD 功能描述:运算放大器 - 运放 Low Noise RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比(最小值):63 dB 输入补偿电压:1 mV 输入偏流(最大值):10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel
TC7660 制造商:MICRO CHIP 功能描述:
TC7660_02 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Charge Pump DC-to-DC Voltage Converter